Dear reader,
I am currently working on a project using the NRF54L15 MCU. There is plenty of documentation available for this component, and the reference circuitry for the...
I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
Hi everyone,
I'm working with the nRF9160 and trying to configure P0.19 as the UART TX pin using Zephyr. Here's the configuration I used in the device tree:
uart1_default...
I have shifted from silicon labs for BLE project. In Si labs we have burn BLE bootloader and BLE application separately. Do i need to do the same here in nrf controller? If...
Hello,
I am using nRF Connect SDK v3.0.1, together with the Find My add-on. Test case TCG013 of the Find My Network Self-Certification Test Cases R1.7 is failing on the...
I am unable to detect any i2c device when connected to the Nordic nRF54L15 DK kit. I have change the voltage from 1.8v to 3.3v and Tried and explore other pins in Port 0 and...
Hi,
I'm working on software for a design incorporating an Ezurio module that uses an NRF54L15 chip.
I'm currently using the peripheral_uart example as a base for early...
I'm new to the NRF5182 and I am currently working on a device where I need to wait for the tx register to send all data before i continue the flow of the program. However...
I'm trying to port your eddystone sdk to GCC. At the moment it is already compiling, but when calling softdevice_enable I get 4 as error code. If I'm right, this means NRF_ERROR_NO_MEM...
Hi,
This time I am trying to work out the UART example.
I got it to the point where it is advertising, but the advertisement is wrong.
When I check with an Android...
Hi,
I have not yet experienced well on the design and development an application using nrf51 series. Your help will be very useful for my work. My question is as following...
Hi,
I have some problems with functions sd_ble_gap_disconnect and sd_ble_gap_adv_stop.
I got critical error when i try to disconnect or stop_adv and my phone is connected...
Hello,
In our application we don't allow bonding. Therefore I'm not allowing the application to send peer data to the bootloader using dfu_app_peer_data_set()...Therefore...
In NRF52-DK, I am currently working on NRF5 SDK 11.0.
In examples/peripheral/spi/pca10040/,
The master spi device is continuously sending "Nordic" string every 200msec...
I've submitted my product using nRF51822 chipset for Bluetooth certification. The BQE asks for QDID of proximity profile. Anyone knows about the QDID #?
Thanks,
Hello,
Is there a way to test packet corruption? My setup would be that I have my FW in nRF52-DK. Then I would test communication using nRF51-Dongle. I would like to force...
I want to connect two nRF51822-BKs and find their proximity. If one of the beacons go >5m away from the other beacon then one should beep/LED ON.
What is the best way to...
I have some troubles to understand the system clock functionality.
I am using a Module from Rigado which uses the nRF52 and has an external 32Mhz osc. on board.
In the...
Hi, I use the following.
Raspberry Pi 3 (RPi3 with Raspbian Jessie 4.4) as a router,
RPi3 is connected to a Wi-Fi router to access the Internet by using the built...
hi
i didn't manage to find detailed requirements on the voltage from the chip.
in the spec i see voltage range of :1.7-3.6v
but its not enough data for designing converter...
hi everyone, I am new to developing apps for nrf51822, and currently I want to learn first, I tried to google a lot around and could not look for the right resources, it would...
