Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
Hi,
I want data read from my sensor (gives continuous data when button is being pressed). and then send it through Bluetooth equipment.(PC or iPhone and so on) But i don...
nRF51_SDK_9.0.0_2e23562
S310
/*
* Setup the gpiote to handle pin events on the MMA8451Q INT1 pin. For the
* accelerometer we want to detect high->low transitions in...
hello everybody,
I'm working in a project & have to do something like security for the connection & be able to do updates to firmwares, someone suggested that doing bonding...
In past , I was able to perform DFU-OTA over BLE transport for a custom board that has nRF51822QFAA (256kB main flash memory) SOC. I tested this functionality with Nordic...
I am trying to setup a nRF51422 Development Kit (PCA10028) v1.1.0 board with ble-sniffer_win_1.0.1 sniffer. I programmed the Dev board with firmware version ble-sniffer_nRF51822_1...
Hi all,
I am using ble_app_uart application to send data to a Bluetooth device. I am sending the data to the Tx Rx Pins of nrF51822 module via an external controller. My...
Hello forum, I've been trying to get SOME alert on my nRF51DK from a phone. I first tried the alert_notification example, but it appears that one has to write a custom Android...
I'm trying to build the blinky example in SDK 11 and load it onto a PCA10000. I'm using the make file in PCA10031/blank/armgcc and am building this under linux. If I use blinky_blank_pca10031...
Hello All,
I am using nRF51822 with SDKv10.0.0 and s110 soft device with RTX os. My project have 5 different threads with 1000 bytes of memory is needed in each thread...
Hello,
I have a project where I wish to have BLE operation while active and use RTC1 as a calendar keeper while in low power mode. So far as I have seen, the softdevice...
Hi all,
I am currently working on the nRF51422 with the S110 version of the Softdevice. The SDK version is 8.1.0.
I tried to get some information back from the Softdevice...
Hi, i am new to embedded system.I want to use nrf52 DK as master and connected with two slaves by two spi channels. since in hardware design, I have designed the chip with...
Hi All, Am using NRF52 and SDK 11.0.0.2 alpha ,
I am using two profiles. I need to Advertise with specific name and parameters for each profile. This profile switch has to...
Hi,
I want to program the nrf51822 with C++ and from what I've found here it should be possible.
But nrf_drv_gpiote.h contains designated initializers wich aren't supported...
