i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
This is both a general tip for users and a question; does anyone have good success with the LIS2DH12 double-tap feature? The 3-axis accelerometer works well but the use of...
Hello-
I'm working with the " Experimental: Wireless UART Example".
Is there any way to periodically send data rather than just typing data into terminal?
hi,
I used nRF52932QFAA ,SDK14.2 uart bootloader.it works well with softdevice loader 5.0.0.But when I download my app(without softdevice),it cannot work.
Flash composed...
Hello Noric Dev Zone members,
we are looking for a Firmware developer supporting us in bringing Hyko to our customers.
What we are working on is making energy heroes in...
Hello,
I want to develop small modules with smart BLE that only sends advertise every 2seconds.
Do you think that the Central module can see all peripherals if the installation...
Hej, I just spent plenty of time finding an answer on above error within here with no luck. Since
there are certainly others facing this problem, I hereby post my solution...
sdkconfig.txt mainc.txt (/attachment/6fb97103178e9eb2c30302351e63ce8f)Can you please tell whether i follow the the entire tutorial as in the link or just the first step for...
Hello, when invoking sd_ble_gatts_hvx, it returned NRF_ERROR_INVALID_STATE (0x00000008), I wanna know what are the list of possible errors, here are a list I made:
CCCD...
Ciao all,
Two weeks ago I have started to learn about beacons and their usage. I have bought pca10040 development kit and designed custom nRF52832 based beacons. After...
Hi,
I've just hit a strange issue with SDK 12.1 on nRF52832.
Usually on BLE_GAP_EVT_DISCONNECTED , sd_ble_gap_adv_start gets called to start advertising and everything...
I am new to nRF 52. Previously i have worked on arduino IDE for programming arduino uno,mega. I have also used MPlabX for programming PIC(MircoChip) series micro-controllers...
Hi,
For the NRF52832, I read that a number of write (per block) is limited before a forced erase of the page. Apparently, the amount of write is 181 times for a block of...
My sensor app is based on nRF UART service and my current case in one sensor (peripheral) one gateway (central).
In a situation where there are two pairs of sensors (S1...
I'm trying to use a low accuracy GPIOTE event to start RTC1. The following code works as expected when using hi accuracy mode but will constantly trigger in_pin_handler()...
Hi, I am using radio with ppi to advertize packets as shown in the mainc file attached. mainc.txt
Even after allocating the access address of Bluetooth on line 196 as set_address0...
Using nRF52832 I am collecting from 8 SAADC channels using example ble_app_uart__saadc_timer_driven__scan_mode as a guide. AIN3 (P0.05) gives incorrect results. Because P0...
Hi,
I have an application that utilizes the dual bank bootloader and s132 soft device on the nRF52832 chip. I am trying to determine the total RAM used and can't seem to...
Hi,
i am using NRF52 and S132V2.0.0 SDK11. i am working on BLE application in which i implemented DFU service to it, so that i am able to observe DFU service and 3 characteristics...
