Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Good Morning,
I need help for integrating a wifi card of this type or another that may suggest. With explanation of connection in the pinp Gpio of the thingy52 board, what...
Hello everyone,
I am looking to start developing something using nfc but I am unable to do so.
I am using SDK v12 and it has nfc examples as well like "record_url" or "adafruit...
Hi,
How to integrate both over-the-air and uart bootloader application for an device? We have a custom board with nrf51822 chipset, and we need to implement the firmware...
Hello,
I'm currently experimenting with the dual-bank bootloader in SDK 13.1. According to the documentation, if the new application can be activated, it is copied from...
Hello everyone,
I'm developing a new device using the nRF52832 but I have 2 questions before I send my PCB to manufacture, I hope you can help me out:
Is there any...
Hi,
Congratulations on releasing nRF Connect v2.0!
Unfortunately, I'm having trouble with adding apps behind corporate SSL proxy. Is there a workaround for this?
Please...
Hi,
I am trying to change the uart example using NRF 52 with SDK 12.3, so that I would hold a button pressed and it would send the time of button being pressed after release...
Hello!
I am putting (with a wave generator) a square wave on pin 17 of the microcontroller, and I want that same wave to come out on pin 18. How do I do that? Do you have...
Hello,
I need to transfer a lot of data over USB. I configured the USB as a USB_CDC_ACM on the nrf52840.
Everything works but the problem that i'm running into is that...
Hi there,
I'm currently using micro-ecc on an nRF52 compiled using Nordic's makefiles and implementing the secp256r1 curve. I'm mirroring this in Node.js using the Crypto...
Hey,
Can the nRF52 support 'Thread' / '6LoWPAN' protocols in the future?
Can the component support it (PHY wise etc) with the right 'softDevice' stack drivers?
Thanks...
I have used nrfgo studio, nrfjprog, jlink commander. Whenever i try, it is unable to find the jlinkarm.dll. i have checked the registry, reinstalled everything, but same error...
I use example ble_app_uart_pca10028_s130, I want to change the connection parameters by changing #define MIN_CONN_INTERVAL, #define MAX_CONN_INTERVAL, but when I use oscilloscope...
