i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hi guys, I'm trying to nail down this TWI issue. PAN 89 is related to TWI being used in conjunction with the GPIOTE module. However I manually wrote my own application level...
Related to SDK 12.3.
Quoting this question :
GPIOTE PORT event generated on the
rising edge of DETECT signal. Please
have a look at section 15.1.2
2)DETECT...
Hello,
I am experimenting with sending large notifications from an nRF52 configured as BLE peripheral with SoftDevice S132 v5.0.0. I having some trouble receiving the notifications...
Hello guys,
I would like to execute code once a scan request from any other BLE device is received by the NRF52 using Zephyr.
Unfortunately, I am not able to receive...
Hi everybody,
I have an issue with my application, I want to use the ble with the same antenna that it use in the development board PCA10036,
Could you please tell me...
When I send 512 Byte from my Android phone I received only 20 Byte. How I can received more than 20 Byte? I used example project "ble_app_uart", SDK 14, SoftDdevice s132,...
I am working with SDK 14.0 . I see two "type" of advertising_init() function :
1-
static void advertising_init(void)
{
uint32_t err_code;
ble_advertising_init_t...
Hi
I have successfully run the light control example for BLE mesh. Now if I want to add another server to the network, how do I do it without bringing the server in the...
I am using the ble_app_uart example from SDK13 and something strange is happening. The code without UART part works nice and I can see in RTT that it can discover every beacon...
Hi everybody,
I have an issue with my application, I use the nRF52832-QFAA with the following circuit, when I open the application Nordic 'nRF Connect', I detect the ble...
We have a software application for the NRF52 with BLE communication. The communication part is based on nordic example “ble_app_hids_keyboard”.
We are using Softdevice...
Hi there,
I am using the uart example with SD130 and added neopixel code from GIT to drive the WS2812B LEDs using bit banging.
I want to update the LED every ms. The bitbanging...
I am getting random data while using saadc example to reading analog voltage applied to pin on nrf52840. i want to read analog output from MQ135 gas sensor, I have applied...
Dear all,
by looking at the sdk code, specifically that of s132 component, I understand that the length of the PIN code is statically set to 6 and cannot be changed.
...
