I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
I have used Arduino for some time and i am very new to NRF. So i am struggling with any thing i do. But i am really motivated to learn it.
Completed setup for eclipse to...
Hi, I am designing a PCB which consists of an analog circuitry (microphone + analog front end) and the nrf52832 chip. I am using inbuilt-ADC of this chip to sample the acoustic...
I use this demo [nRF51_SDK_10.0.0_HID_DFU_090216.rar] (/attachment/27e0b68cff3ffe4959299fcae336e844)
change rep_map_data[] add mouse and Consumer,but restart is no work ...
Hi,
(I'm a computer scientist, please be kind)
In the below attached image, I have collected the data outdoors (so no signal reflection or signal fading) from a single...
Hello all,
I am using nRF51822 BLE SDK 9.00 PCA10028. I want to configure the gpio pins as input to sense the voltage as high or low. how to configure it please suggest...
hi
i'm developing to nrf52832, sdk14.0 version.
for example, ble_app_uart project..
NRF_LOG_INFO("UART Start!");
printf("UART Start!");
-> In serial program,...
I have an application that do SW download to STM32L151 processor using NordicDongle with MasterEmulator.dll (Version 2.1.13.14)
It works good on my desktop windows 10 computer...
Hello,
we are trying to test the mesh functionality with nrf development kit. We erased the flash on the dev kit and we programmed it with softdevice version s132v3.0.0....
As stated in the topic. We use BLE to simulate UART. As for now, we have defined our own UUIDs but there would be more straight forward to use the well defined and used one...
Hi,
I have known your board support jlink ob；I want to debug through it ;
I want to know if i need to buy the software-license from SEGGER ？
and if i need buy the software...
Now facing the problem "After disconnected, the electric current increases"...
I think softdevice is working hard even after disconnected when connecting once.
Could you...
Hi,
I'm trying to write unit tests and have arrived at the point to write tests for ble characteristic addition to a service.
To offer some background, I have written...
Hello,
I use NRF51822 and I try to output UART message onto hyperterminal program.
but every message I send it contains "APP:INFO:" in front of the message.
like...
