I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi, im using nRF 52 DK. I interfaced mpu 6050 by using the example found here (BLE example found here is not working properly, dosent connect with uart app). I'm particularly...
Hi,
Does the erase target in the makefile completely erase the flash? I'm having strange errors when trying to read the flash (i.e. I can't read anything from flash, even...
Hi, Schematic and Code As shown above, VCC 3V (DEC2 and VCC open) current is only 3.8uA, but VCC 1.8V (DEC2 and VCC short circuit) current exceeds 1mA, what am I mistaken...
Hi,
I seem to be stuck on a rather simple problem here which I am unable to figure out. I am using SDK 12.2 with PCA10040 board.
When I am compiling the experimental...
Curious as to why the Buttonless DFU Example in SDK 12.3 utilizes FStorage to save settings rather then simply setting a flag in the GPREGRET? This seems like a much more...
Hi guys, now i have done the example as the light control demo description, but i have a question about that how i can let the light server to leave the network?
HI team,
I use the S132 ,SDK_12.3.0 , nrf52832 PCA10040 v1.1.1 develop board. I met a problem when I do experiment with twi_sensor example code.When nrf52832 finished transfering...
Hello,
I'm currently running our RTC using the default resolution of 32.768 kHz (30.517 micro-seconds), which means that we are not prescaling. If I desire to have a larger...
Hi,
i have a Bluetooth PCBs that i designed using nRF51/52 chips and i'm wondering if there is any way to connect them to a web-server using a gateway.
i don't know...
I've looked through the Devzone, but couldn't find an answer to my question.
We are looking to automate the OTA process. When our nRF52 device is charging, it advertises...
Hello,
I would like to know the best practices to update a passkey for bonding.
For the moment, I have a static passkey that I set during ble initialization and I can...
To start off here, I'm using a Laird DVK-BL652-1.0, which according to Laird only needs to be re-configured to use the internal oscillator, but is otherwise very similar to...
Folks,
Have been using Keil MDK Lite in the past, in a Win VM. Larger code (over 32KB) plus the convenience of running without a VM layer have led me to switch to NetBeans...
