I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
What development kit should I buy? Is this the right one?
www.mouser.hk/.../
What software IDE to use?
Does Keil offer free version for limited code size? What...
trying to build a simple example in sdk 11 just to run it on the nrf52-dk
of course it is missing pieces, else life would be no fun, apparently...
oh, i don't know,...
Sorry for asking as not familiar with BT terminology and un-sure which fold means what, grateful pointer to example (in SDK or similar) that can run on the dev kit. That is...
What is "1 Mbps Bluetooth low energy mode" for nRF52832?
How was the spec. changed from my old year 2013 understanding that BLE is low speed for sensor, sending tens of...
I can read temp value by pulling flag but I Want to do that by interrupt
I added this code to my Keil but interrupt on temp didn't work.
I use Adc interrupt like this definition...
Hi,
We are using NRF51 and STM32F0 on our custom board and one of our customer's requirement is the ability to program both of these MCUs in the factory. They would like...
I am using the mbed compiler.
When I produce code using the "App with Bootloader" option, I can do FOTA updates and my code runs fine, as long as I don't enable the ble uart...
Hello together,
we are running the DTM in different modes to check the module (nrf52832, sdk 5 version 11). The carrier test gives us a current consumption that meets the...
Hi
I try to program Insight ISP 130301 with a hex file, which works on nrf51 PCA10028. Unfortunately, it doesn't work. I try to loop for each pins and set it's state, and...
I'm trying cominicar me through Termite between the application plate (nRF51-Dk kit) and a device that supports BLE, but the connection between PC and the kit application...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Hi again, I posted earlier in another post that my writeCharacteristic is responding with status 6.
Details:
Android version: 5.1
Nordic device: nRf51822 S110
I have...
Hi
I want to use nrf52 LATCH register.
I can see the correct bit set in the register, but I am unable to clear this bit.
I have tried NRF_P0->LATCH =0xFFFFFFFF; for my...
Hello
I am doing a PCB design using nRF51422-QFAC chip. I did based on nRF51-DK but now I would like to change for a SMD antenna (2450AT18A100 from Johanson Tech.) instead...
