I had the nrf5340 DK working for a few weeks now, and while working with SSD1309 OLED peripheral, was trying out a simple display application. Couldn't get the display device...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
در دنیای پررقابت صنعت غذا، موفقیت رستورانها، هتلها، تالارها و آشپزخانههای مرکزی وابستگی زیادی به کیفیت و کارایی تجهیزات آشپزخانه صنعتی دارد. برخلاف آشپزخانههای خانگی،...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hello All,
I have modifies the Spi Master code to communicate with an ADXL345 Accelerometer. I set up my powermode and the percesion in the setup phase. However, when I send...
Hello, Nordic Team.
In my program, I have to change the value of the characteristic before start. I write:
case ACI_EVT_DEVICE_STARTED:
g_aci_state.data_credit_total...
Hello,
I want to make my Arduino coupled with the nrf8001 advertising a simple data (an integer). There should also be a possibility for dynamically changing the advertising...
I have a Jayconsystems breakout board for the nrf8002 bluetooth chip. Nothing is connected to the breakout board and the chip is unprogrammed. My current meter reads 6.0 mA...
The nRF8001 Product Spec says,
"Dynamic Window Limiting reduces the average current consumption by reducing the window widening of the receiver ... Enabling this feature...
Hello,
I am trying to play alarm in button click using nrf code. I am using Nordic nRF51822 device and trying to integrate with android device. When I am using linkloss then...
Hey guys,
Working with the simple be_app_beacon example on nRF51. I’d like to be able to stop and start advertising. But after stopping advertising, I’m unable to start...
Hi，
Can the examples in <keil_location>ARM\Pack\NordicSemiconductor\nRF_Examples\9.0.0 of PCA10028(nRF51422 chips) be use on nRF51822 chips? Or how to modify it to adapt...
Hi
in my application I use about 8 app_timer instantiations (so 8 x app_timer_create), with various frequencies.
I noticed now that one timeout handler is triggered twice...
any body know about android code for pairing with ble (nrf51dk)?
please help i want to pair my android app to the chip. app is discovering the chip but not able to connect...
Hi
nrf 52832 is able to run in 64 MHz using external 32 MHz crystal.
I wondered if I can use an external 16 MHz crystal, and get the CPU to run in 32 Mhz.
Thanks
...
Hi, All
sdk v7.2, IOS 9.1
I know after peering with IRK, iOS will connect 51822 actively.
There're some issue in my project. It's not certain happen.
At most of...
I developed an application program and I have a hex file generated from mbed compiler, and would like to know if I flash this hex file using a J-link interface on NRF51822...
