Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Hi,all
SDK:8.1.0 51822
S7 Edge（android V7.0）
i use the sumsung S7 Edge and the oppo R9S connect with my device,nRF Connect is often note:
GATT_CONN_TERMINATE_LOCAL_HOST...
for ble_app_ancs_c_s130_pca10028 example of sdk11,s130 version 2.0.0
The preferred RAM,ROM and UUID COUNT is shown below
FLASH (rx) : ORIGIN = 0x0001B000, LENGTH = 0x25000...
Hi All
I am trying to build hex file using eclipse id on Mac. everything looks ok, as it eclipse build file without any error but its not working on nrf52 dk.
before...
Now I’m using nRF51822 with S130 SoftDevice.
There are two kinds of devices which is just for scan(A) – 20EA and both scan and advertising(B) - 2EA.
I found that B just...
Hi,
My question is similar to this devzone.nordicsemi.com/.../ but I can't get it to work.
I am using SEGGER_RTT_WriteString and sprintf for debugging, but I am not able...
Our mobile app is currently running atop of easyble and nordicble.js/Cordova. This library works great on all Apple devices, however, Bonding with Android devices of various...
We have done a custom PCB believing that we could use P0.0 as analog input. Now we kind of found out that we cannot, and will change the PCB design. Given that we already...
Hi, I am using nrf24l01+ tranceiver in a project I am willing to sell. I use modules with external antenna and without it. I need the CE certification of the module. Where...
I have used NRF52840 and SDK 13.0.0.
When I have used USB or ESB one by one - all is Ok.
But when they are used together - usb driver goes into an infinite loop here:
...
Hello.
I am developing a project on nRF52832 using SDK 13, in which I need to transfer up to 300 bytes of data from iOS device via my dedicated app (in the background) to...
Hi,
I read in the documentation that one can loop a complex playback. The way I understood, one could load a first sequence (say seq1) and a second sequence (say seq2)...
Hi Nordic Team,
i am working on nrg52 to glow a RGB LED with white and Yellow colours. configured the RGB pins to three different Gpio (A2,A3,A4).
for this i am using...
I have an application where I read a IMU at around 60 - 80 hertz.
How should I configure the S132 so I can send my 14 byte string packet with a constant time interval?...
Good evening (at least here...)
I successfully developed an application with Keil on the Rigado EVAL board with the following steps:
nRFgo Studio -> erase all and...
Hi,
is there a way to make a all in one bootloader image which includes Softdevice and APP in one zip?
And is there an example of the DFU via a Master uC. My setting is...
