Hello,
I'm developing my custom sensor application. It's a matter over thread device. Before final product I'm working on a NRF52840 DK PCA 100056 v3.0.1 and NCS 3.02. It...
Hello,
I higly need to run twister unit tests in debug mode with breakpoints, step by step, spies and other debug tools in vscode. I did not find a way to do so.
Is...
Dear devzone, Can our nRF52840 detect 20 nanosecond voltage fluctuations using COMP? For example, if I set a lower threshold of 20mV and an upper threshold of 60mV, and the...
Hi nordic： What is the peak current of NRF9151? The relevant parameter cannot be found in the datasheet, while it is available for NRF9160.
Best Regards
JERMI.JIN
I'm using the nRF52840-DK part number 1490-1072-ND I ordered last week. In both nRF Connect for Desktop and the VS code extension the device wasn't able to detect. Tried two...
Hello, this is probably a very beginner question but I don't know how to configure interrupt for the GPIO headers on the nRF52840 dev kit. I tried to search in this forum...
In the documentation for the secure bootloader, it's mentioned that the provisioning data gets stored in OTP memory for some chips (e.g. nRF5340). Is there a way to know what...
Hey guys,
With the ble_app_exemple, I manage to add the FDS libraries. Unfortunately, when i run the example in Debug, I got error 2 for fds(FDS_ERR_NOT_INITIALIZED). I'm...
Hi,
I am using nrf51822 module and sdk v12.2.0.
I was compiling code under ubuntu. I observed that pca10028 is configured for nrf51422_xxac target.
But i want to use nrf51822...
Hi,
The NFC function is set to read only in my application. I don't want to wake up my system when someone tap on my device to read the NFC data. (assume this method can...
Could someone confirm whether there are schmitt triggers on the nRF51822 GPIO. I found the following thread that mentions them, but it also is discussing the nRF52 series...
Arm Gcc (using Eclipse Neon) |
SDK 13.0 |
nrf52 DK (PCA10040) |
tried soft device 4.0.2 and 4.0.4
I can successfully compile and run the example -ble peripheral- ble_app_hrs...
Are there any particular practices or instructions should i follow if I want to write a custom library
We are trying to write a library for LEACH protocol and it is a network...
I spoke with someone at Nordic who seemed to imply that utilizing the radio does not necessarily tie up the Cortex processor on nRF5X devices. Is this true? It seemed to me...
I am trying everything.
In sdk_config: #define UART_DEFAULT_CONFIG_HWFC 0
In the nrf_cli_uart.c I changed it to APP_UART_FLOW_CONTROL_DISABLED,
in the pca10040.h I...
Hi , I have 2 nrf51822 borads. One is with nRF5_SDK_12.3.0_d7731ad\examples\ble_central\ble_app_hrs_c and the other is with nRF5_SDK_12.3.0_d7731ad\examples\ble_peripheral...
I would like to use the ble_app_uart_c example, found here , to connect to a custom peripheral. What values should I change in the central device code in order to connect...
I know that BLE is not suitable for high-volume streaming.
So how do BLE earphones stream audio?
Does it use with bluetooth classic protocol?
And I coundn't monitor...
Hi,
I've one central and one peripheral devices. I'm trying to make a connection between them, perform a bonding process and finally add the peripheral id in the whitelist...
Hello All
I am developing BLE based home automation system using nRF51422 DK for my research activities. now i am planing to make separate PCB nRF51422 device alone. i...
Hi,
I'm trying to get the RSSI of incoming 802.15.4 packets using otLinkRawGetRssi() , but I need only RSSI from one specific device. I tried to use whitelist ( otLinkSetWhitelistEnabled...
Hi, I ran the example code ble_hrs_c in nrf51822 16KB RAM version and 32KB RAM version. The 16KB RAM version works fine. But in the 32 KB RAM version, peer_manager_init(true...
