Hi，everyone:
We are developing a Nearby protocol combined with UWB, which needs to communicate with the Bluetooth of Apple phones and then use UWB to measure distance. We...
As shown in the figure, MCUboot has a boot_go_hook function. I'd like to define this function in my own project and compile it into MCUboot. Since I'm using single slot DFU...
Hi,
1.In ncs v3.0.0, can both USB DFU and UART DFU be enabled simultaneously on the nRF5340 DK board? 2. If USB and UART DFU can be enabled simultaneously, then how should...
Hello,
We are working on establishing a connection between one of our existing Bluetooth modules (cypress) and nordic based module to provide backward compatibility with...
Hello,
I’m working on a project based on the nRF Connect SDK v3.0.0 Matter Light Bulb sample , using the nRF52840DK. I aim to implement IPv6 support and enable Matter over...
I am trying to create a partition on my external flash using littlefs
Here is the line that is returning me an error
FS_LITTLEFS_DECLARE_DEFAULT_CONFIG ( storage ...
We are developing HW that includes nRF9151 running DECT NR+ with the Wirepas stack for mesh connectivity between multiple units. The product is expected to move between geographies...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hello,
I am planning to use an atmega32u4 as a micro controller for a keyboard, and I'd like to use a NRF51822 as the bluetooth sender.
As i've read, NRF51822 is BLE...
I would like to learn a little more about the process of negotiating a connection interval between an iOS and Android central and a nRF51 peripheral.
So, here are my questions...
Hello,
I purchased a nRF52DK to migrate my older projects running on nRF51822.
Version of the board is V.1.1.0 / 2016.19
I followed the 'Getting started' guide from...
Hello,
This is a DFU custom project...the core problem is that I cannot erase the bootloader settings page from the chip.
While trying to use a slightly modified version...
Hi
In current Desktop 2 project, We know that software device stack takes 48-bit random device address from FICR registers (DEVICEADDR[1: 0]) for BTLE. Each nRF51 has unigue...
Hello, I am devleoping a pc station using pc-ble-driver.
I was successfully able to install it on one of my computers but am facing a problem installing it on my surface...
The micro-ecc works well when I load micro_ecc_lib_nrf52.lib in keil5. However, the author suggest copying the uECC files into the project, so I include uEcc.h but fail in...
For the nRF51822, the documentation for ECB mentions it being used to
Encrypt/decrypt 16-byte data using
current key.
But it doesn't offer any methods to decrypt...
Hi,
Am using SDK 11.00 and NRF52 platform.
Am following below steps for dfu support.
1.Flashed Softdevice 2.00
2.Flashed dual bank ble Bootloader
3.Using nRFTool box...
Yan,
You mentioned these UART examples: examples\ble_peripheral\ble_app_uart or examples\ble_central\ble_app_uart_c I was not able to find them on your web site....
I have intention to use 52810's PWM output to drive motor. The timing requirement are critical so
hardware PWM is essential, rather than CPU generated waveform output.
...
Hi,
I am trying to increase MTU size for transfers and it works up to a size of about 72. After that I get an error.
Thanks to Sigurd I now know that it is when calling...
Hi, I've an application developed with SDK v8.0.0 and S110 v8, that is using the bootloader to start the main firmware and to start the DFU OTA (in case the user request to...
