Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
Hi.
After 3 days I've finally got littleFS working on a custom nRF52840 board. I am using nRF connect SDK v2.9.0 which includes Zephyr v3.7.99 with some additional Nordic...
Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
Hi,
I’m working on a Matter application using the nRF Connect SDK v2.9.2 . I’ve added the AirQuality cluster into my device with sub-sensors: CO₂, PM1, PM10, TVOC, and Temperature...
Hi Team,
Recently we did a network related testing for our CL5G modem (nrf9160) and observed a problem, in this test we used a nmap tool, this tool will search for open...
Steps to reproduce the problem
Create a new application based on the Matter Light Switch example of the SDK 3.0.2
In prj.conf set CONFIG_CHIP_FACTORY_DATA_BUILD=n
...
I am developing a mobile apps using Nordic . I am seeking for Nordic Semiconductor nRF51822 SDK documentation for objective-c(iPhone) as well as Android too. Is there any...
I connected up +5v to the external power pins of the nRF52dk. I see +5 at TP14.
When I set the power switch to 'on', the board does not boot.
Is there something else...
Hi:
Looking in both SDK12/13 I cannot see any examples related to an HID Joystick/Gamepad.
It looks like somebody asked a similar question here: devzone.nordicsemi.com...
I am using nrf51822(pca10028)
i used the timeslot API tutorial in devzone..and it worked fine but i want to integrate the radio receiver example along with this.
nrf_radio_signal_callback_return_param_t...
Hi
In the SDK13 release notes and even in a few posts in the DevZone the new S140 5.0.0 Alpha2 Release is mentioned. I looked for the download link in the product page...
Hi all
I'm using the GATT server on the nRF51822 with the SoftDevice S130 V2.0.1. I've implemented a service and a characteristic which supports only write requests (including...
Here is my question.
I always disable uart after I send data.
NRF_UART0->TASKS_STOPTX = 1;
NRF_UART0->ENABLE = UART_ENABLE_ENABLE_Disabled;
this was write in the...
Is there a compiler/makefile flag that allows for 64bit printing?
I have included inttypes.h, and tried both %llu and "PRI64" as shown:
char scrbuf[30];
uint64_t time_alive...
Hi
We are using NRF52 and SDK 11 and S132.
The nrf52 acts as a central and selectively connects to the closest phones (ios) that are acting as a pheripheral.
For this...
hello,
nordic's engineers, need your help.
(1) the first problem : can not set VDD output to 3.3V
From nRF52840_Product_Specification_v0.5, it says:
High voltage mode...
Hi all! I am attempting to download a file from a web server to an NRF52832 using the Nordic IoT SDK version 9.0. Are there any good reference librarie? I found a few for...
Hi. I'm using nRF51822, SDK12.2.0, S130 v2.0.1.
I'm using nRF chip as Multi-connection Central and 1 Peripheral as well.
My event function is
static void on_ble_evt...
I've tried everything I can find on this topic and I still cannot get P0.09 to behave as a GPIO pin. Does it have something to do with the way I'm attempting to initialize...
Hello,
I am working on a custom PCB with a nRF52832 and I've been unable to get the ON IDLE power under 480uA. Here are the basics regarding the setup
nRF52832 Rev...
