Hi, I am running openthread on the NRF54l15 DK. Whenever I am debugging and hit the breakpoint or pause the program, then on resumption my app crashes. How Can I debug while...
Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hello, I’m working with a combination of nRF5340 + nRF7002 + NPM1300 , and I’ve only changed the I2C pins connected to the NPM1300 to sda pgio1.4 and scl gpio1.6 .
SDK...
I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
I've seen other threads about the issue:
- https://devzone.nordicsemi.com/f/nordic-q-a/117267/light-bulb-sample-works-on-nrf52840dk-and-doesn-t-on-nrf52840-dongle
- https...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
Using the peripheral_uart example routine from the NCSv3.0 library with the 54l15 chip.
1. compilation command: west build --build-dir build . --pristine --board nrf54l15dk...
I'm using Arch Linux, with kernel 4.9.6 on a 64-bit laptop. Using a window manager with no desktop environment.
I'm trying to install Segger Embedded Studio 310i , which...
Hi,
I am working with nrf52DK and Sim800l, I want to send some data using GPRS commands like AT etc.
I am having a market build module for Sim www.circuitstoday.com/....
Hi,
I am using the example code supplied by the blog for reading humidity from the HTU21D sensor using TWI . My humidity and temperature readings are constant and never...
The code generated from the BDS plugin (v.1.2.4, found here: question including link to v1.2.4 ) is failing because of missing references to boolean_t and bds_boolean_encode...
Hi, I need a simple timer that interrupts every second. I'm trying to use the code from the sleep timer, but it isn't working. this device is the PRX, so i don't want it go...
Hi.
I'm using the arm_sin_f32 function to generate an array of sine wave values. However when this function gets called the softdevice crashes.
I've included:
#include...
I've been trying to chase down some of the engineering samples of the nRF52840 for a prototype with no success from distributors here in Japan (have tried Digikey and Mouser...
Hello,
I know that the NRF_TEMP peripheral is a restricted peripheral and should be accessed with the sd_temp_get function when the soft device is running. Heck I even...
Does the NFC library globally disable interrupts at any point? We're trying to track down an issue where our code occasionally misses an I2C event during NFC read/write.
Hi all,
when I try to send 6 bytes of 0xFF, the last bytes change. I use SPI in mode 3. I use the NRF52832 on a custom board using SDK13 with sd v4. See the following screengrab...
Keil4 compiler in the compiler C and assembly of the mixed code, the error content is: Branch offset 0x00000388 out of range of 16-bit Thumb branch, but offset encodable in...
This function contains a lot of tags that need to jump, but at compile time there are these errors.
this is ARM compilation and C mixed,How should this error be handled?...
Hello, I am trying to develop on the NRF52. I have the development board and have been spending time with the SDK and documentation. I understand how the GPIO should work...