Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Using Segger , only the BLE template is advertising,All other BLE apps such as BLE_UART, will flash the leds very fast but will not show on any Apple device on the Bluetooth...
We have an ISR parsing incoming serial data from the UART. When a valid packet arrives, I'd like to be able to wake the core from whatever low-power state is entered when...
That is probably an old topic, but after doing some research I could figure it out: calling sd_app_evt_wait() on my nRF5832 + nRF5 v11.0.0 SDK + s132 causes my chip to reset...
Hi
I've some troubles with the ble disconnection of S110.
Always when I call the sd_ble_gap_disconnect function after successful connected, the error code 8 NRF_ERROR_INVALID_STATE...
As I can see, I flashed Zephyr to Carbon 96 board, I don't fully understand the process,
I mean, I see .bin and .elf files but i don't see boot.img file, how do i make a...
The nRF52832 datasheet refers to a transmission of multiple packets in Figure 37. I have attempted to load multiple packets to the radio FIFO using nrf_esb_write_payload(...
Hi All,
I have developed an application on the RedBear BLE Nano2, and am trying to port it accross to a custom nRF52 board.
The Hex that the Arduino IDE outputs does...
I have an application which requires protection from passive eavesdropping, but not man in the middle attacks. I want to enforce the use of diffie hellman key exchange.
...
Hello
i am using Nrf52840 with sdk 132 and version 12.2
i am using the Heart Rate example as template.now i am just testing.
Before making connection,i like to Advertise...
I have a sensor which has output in the range of 0-5V. I want to connect it to an nrf51822 GPIO pin and to be able to read the value via it's 10 bit ADC. Is there any guide...
hello, there my application is like that...
(1) calculate size of receive buffer. than read that size of data.
again new data comes, then again calculate that size of...
Issue: With my external antenna design, I get lower dbm than PCB antenna (nRF51DK) with same distance.
My external antenna design: -70dbm
nRF51DK: -40dbm
In this...
Today when I started power profiler kit, it suddenly started to show peak values like 80 mA. This has not happened before, but the values with the same hardware have been...
In the data sheet of the NRF51 and 52 there is mention that sensitivity of NRF51 is -96 dBm and NRF52 -98.
But I read some where that when RSSI is -90 then that signal...
