Hello All
We are trying to integrate ST7305 driver with NRF connecct SDK and are unable to get the driver to work using the extrnal module method mentioned in the NCS Intermediate...
We are currently working on a project using Enhanced ShockBurst (ESB) and would like to enable Front-End Module (FEM) support with the nRF21540.
According to the Enhanced...
Hi,
Is it possible to make the MQTT connected device receive the Shadow config updates and AT Commands immediately? Based from our testing, the device only receives the...
Hello, I would like to appply change in asset tracker template FROM nrf_cloud to Firebase Realtime Database.
https://github.com/nrfconnect/Asset-Tracker-Template/blob/main...
Hi there, I´m totally new to Zephyr & Nordic, started with some Trainings on NRF52840DK and jumped in with a device driver developement where I took a availalbe out of Tree...
Hi! We are having problems pairing a nRF52840 against linux (ubuntu 25.04). Pairing fails instantly, before any passkey is shown on the host, returning with code 9. Short...
Hi All, I encountered an issue while trying to use both Bluetooth and ESB in the same application. To clarify upfront: I am not using these protocols in parallel. Also, I...
Hello,
is it possible to use the RSSI value of the NRF51822 for collision avoidance?
How long does an RSSI measurement take?
I'm trying to implement a discovery protocol...
Hi all! I used PWM module of nRF52832 to create the PWM but i don't know how to update new value to duty_cycle. This is my code. I used Button (Pin 13) to set a new DUTY_CYCLE...
I am trying to set custom value to advertising address. The code snippet is below. I am getting error code 0x10.
static ble_gap_addr_t * p_addr;
uint8_t itr_i;
p_addr...
Hello,
I have a question about stack usage. I use nRF51822 SoC, 12.2 SDK & IAR 7.60.1. I am interested in stack usage. Have you done any estimations? Or may be you have...
We have a BLE application where we need hopping through nodes. I have shown below how it looks like. We don't want mesh network because we don't require node to node communication...
i use nrf52_DK to debug PDM with a digital MIC, and select the P0.09 for the PDM clk, but i have not see any clock signal output, is it right? and i also haven't see the convet...
Say I have 3 records, then I delete them and collect the garbage. If I try to save a new record again, it will be saved with a record ID 4 , but it should be back to 1 after...
I want to use the development kit for Bluetooth 5.0 IoT product development.
Is there already a bluetooth mesh software available for the nRF52840 development kit?
Or...
I am working on time synchronizations between different nodes in a mesh network. I have earlier worked on the radio and the ppi examples given. I wish to generate time stamps...
Hi
I would like to prepare a provisioning hex file for my firmware.
Can somebody supply an example how this could be made?
I'm using gcc toolchain, Eclipse and SDK...
Hello,
I am using sdk12.2.0 and pca10028 dk. I am using one code downloaded from unknown source. The code is used to store data in flash. When I compile through keil I don...
Hi,
i try to establish a communication between 3 sensors in the following way!
Node 1 should broadcast messages to Node 2 and Node 3 as Peripheral.
To establish a...
Hello,
I am using pca10028 and sdk 12.2. I have interfaced temp sensor with nrf51 and now I want to store that data continuously in memory of nrf51. I want to store min 4k...
Hello, I want to program and debug the nrf52840 device but I'm kind of stuck at the programing range/address issue.
I'm using my customized board so I doubt Nordic Semi...
