Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
The question has been answered before, but the answer references a document called nAN-29 at this link: www.nordicsemi.com/.../73843444 . Which doesn't seem to be working...
Hello,
We use the PCA00031 dongle running the MEFW 0.9.0 in our production environment to validate a sensors accuracy. The PCA is controlled by a C# test program using...
Could someone explain the pin numbering scheme in regard to the interrupt setup handler?
To be specific, what pin number should be passed to nrf_drv_gpiote_in_init for...
In the ble_app_att_mtu_throughput example for the PCA10056 I am getting a "fatal error in the include chain" pointed from the #include "amt.h" line in amts.c. Specifically...
Hi,
I'm working on a firmware that is used in a nrf51822. I discovered an unwanted behavior of my system.
When the system is in power_manage mode, it can wake up in two...
● device : nRF52832
● sdk : 13.0.0
● softdevice : 4.0.2
Hi,
I have a problem with change mtu size.
I changed mtu size in sdk_config.h, but android application can't read...
Hi,
I am working on custom Board with nrf52382, I am using the mma8652 accelerometer for different functionality(prior is single and double tap detection).
Initially...
Hi,
Because of the compatibility issues I'm trying to use SDK10 for my nRF51422 device,
the problem is that I have flashed the S130 softdevice and the ble_app_uart, and...
I want to use FDS in my application. Lets assume I do not have a bootloader. This is part of my linker script describing memory regions.
MEMORY
{
FLASH (rx) : ORIGIN...
I am using proximity profile for my custom board as a tracker.I would like to make the services read/write operations accessable only to my andriod app.Others can connect...
Hello,
Recently I purchased a BLE Nano Kit with MK20/ DAP Link USB Board - Bluetooth 4.0 Low Energy Module Development Board from Fab2Lab and I was trying to use the nRF...
Hello,
We are new in Bluetooth development world. We want to use Laird's BL652 module. At beginning we want to use smartBasic and later Nordic SDK directly. Is it possible...
HI Nordic Team,
I had a production run of 5000 units. Used nrfjprog script to program the nrf51 .
Used the following commands:
nrfjprog -f NRF51 -e
nrfjprog -f NRF51...
