Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to store two floats and one 8 character string in fstorage.
I solved it by using 4 uint32 types stored in flash, I got it working in the ble_app_template example...
Good morning,
this is Algocraft (www.algocraft.com), an high tech company whose core business is to develop, design and market a wide range of professional systems dedicated...
Hi everyone,
I'm using a custom wrapper ( github.com/.../arduino-BLEPeripheral) with softdevice S130 v2.0.1. I've extended the wrapper to allow simultaneous advertising...
I am trying to implement a simple example with custom profile by building upon
the tutorial given devzone.nordicsemi.com/.../
My profile is something like this:
Service...
Hello,
My application perform reset periodically. When It does a reset the bootloader need to initialize the softdevice with SD_MBR_COMMAND_INIT_SD before calling sd_softdevice_vector_table_base_set...
Good times,
So I finally put in the tweak to enable the GPIO 9&10 pins to be used for GPIO instead of the default NFC mode. Must remember that reset for it to take effect...
Hello,
I'm testing ble_app_hrs example by nRF52832 DK.
When i change NRF_BLE_GATT_MAX_MTU_SIZE up to 158, the example project run properly.
But, when i change MTU...
Hello, I am using nrf52832 custom board, with SDK 11.0.0 and s132_nrf52_2.0.0 and trying to dim led. It seems the only suggested solution is to use the pwm driver. I was wondering...
Hello, im experimenting around with the nRF52 DK (and nRF51 DK also)
Now I have following setup on nRF52 DK:
SoftDevice: s132 nRF52 v2.0.1
Applicatoin: Example Project...
I have the option to connect nBLE51822 to MCU via SPI, UART or I2C. But is there any advantage of using SPI/ I2C interface over UART interface while connecting nBLE51822 to...
my code is below.
git_mpu9250_dmp.zip
Hello.
I use nRF52 & MPU9250.
I want to use DMP,
but I can't read data with DMP.
Because it have failed that writting firmware...
Hi there,
What is the recommended development tool setup for nRF52 Preview DK on Mac OSX?
Your guide for SDK 0.9.1 seem to rely on Keil which isn't natively available...
Hi all,
What is the difference between the app_mailbox and the nrf_queue api?
The documentation says:
A)
The mailbox library provides functions to safely exchange...
Hi team ,
I'm using sdk 12.1.0(E:\testing\examples\ble_central\ble_app_hrs_c\pca10028\s130) example.I want to change to this BLE_GAP_ADV_TYPE_ADV_NONCONN_IND in above example...
