Hi Nordic Team,
I am trying to implement a secure boot chain on the nRF54L15 DK using NCS v3.4.0 (LTS) with the following configuration:
Board: nrf54l15dk/nrf54l15/cpuapp...
As in subject, psa_aead_finish function generates incorrect tag for AES-GCM when Nordic proprietary library is used.
Works fine with Oberon backend.
Similar problem reported...
Hi, I have a question with regard to the nPM1100 PMIC and entering ship mode (not exiting it).
If I am interpreting the datasheet correctly, the SHPHLD pin must be held...
Hi Nordic Support,
I am facing an issue where the peripheral registers are not visible in the Keil debugger during a debug session. Only the core registers are available...
Hi:
Use nRF54LM20A_DK.
Use ncs 3.1.1.
And this is source code:
The following error occurred:
« *** Booting nRF Connect SDK v3.1.1-e2a97fe2578a *** *** Using Zephyr...
Hello, I use the NCS v3.3.0 (ncs\v3.3.0\nrf\applications\nrf_desktop). Can the desktop dongle connect to two keyboards at the same time? Development boards: two nrf54lm20...
With SDK 3.3.1 I do not get the <inf> logging messages when building the Hello World app unless CONFIG_LOG=y is added to prj.conf.
Perhaps this is left as an exercise for...
it will try to lower the RF, TX power
Bluetooth is not sure what to do because the first time
What things do I need to solve ? ex)component, software,hardware...
Good morning,
I have already implemented my application based on nRF51822 and SD110 v8.
In what regards bonding, I use a static passkey and it works fine.
The product has...
I will use the functions in app_timer to set a timer to fire every 3 seconds. I want this to occur "forever" (e.g.until a restart of the nRF51).
To avoid a timer overflow...
Hi,
I am using the nRF51-DK board as a central running with ble_app_multilink_central_s130_pca10028 sample application. I am using SDK version 9.0 with Keil 5.14 version...
Hi all! I am using the nRF51 DK and I am trying to use the elements demo APPs that Nordic provide - the Beacon app. after the downloading of the app and watching it working...
Hi
In my application, I use some of the IO pins for a multi-purpose sensor interface, that I would like to be able to configure when the application is running. The interface...
Hi,
Can anyone help me where can find the example ble_hr ? I have changed the main file and it is saved and now I want the original example that was in C:\Keil_v5\ARM\Device...
I have IAR Embedded Workbench 7.40 installed with nRF5x_MDK_8_0_3_IAR.msi. However when i select nRF52832_xxAA i get the below message:
WTD: Unavailable option selection...
In IAR Embedded Workbench for ARM, version 7.40.3.8938 (w/ common components version 7.2.4.3784 ) with nRF5x MDK for IAR version 8.0.3 .
When selecting the target in General...
Hi,
I have a couple of nRF Beacons and want to change the program so that it scans for iBeacon packets before starting to advertise.
The flashed program is just advertising...
I just would like to test my new nRF51 DK using the SDK V9. However, I could't build the "blinky_blank_pca10028". It always shows the following error.
Error: *** Project...
Hello,
I m using the UART in low power flow control mode(app_uart library). When the CTS line is asserted, what is the maximum time that the UART module takes for the UART...
hi everyone.
we are migrating to nordic nrf51 series (before we used ble modules from another vendor blugiga which depends on cc2541 chip) so I m pretty new at nordic nrf51...
Hi all,
I'm using the pca10031 which contains the nRF51422 chip; as a packet sniffer to sniff the communication between my S5 samsung and my pca10028, but I struggle while...
