Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi, I am using nrf24L01 for my application. I have to question:
- Is it possible to bypass SB protocol (I take into account possible error in exchanged packets without preamble...
Hello All,
I am following this tutorial.
https://devzone.nordicsemi.com/tutorials/b/bluetooth-low-energy/posts/ble-services-a-beginners-tutorial
I have modified "nRF5_SDK_15...
Hi.
I refer to this document. Stopped at Step.B1 now.
If you go to that path using CMD and then type "make", you will see the following problem.
'make' is not an internal...
Hello,
In my project (nRF52, SDK14.2) I have spi data flash connected to the MCU.
I'm trying to use SPI transaction manager library (nrf_spi_mngr) and face few questions...
I don't know how to use nrf52840 dongle as a sniffer. I look at the official routine. It looks like it really doesn't function as a sniffer. Is this what it is. If not, how...
Hello, we are trying to get a new laptop compiling and debugging with an older project. The old project uses SDK5.2 and SoftDevice 6.2.1. When we open it we get the error...
Hi Everyone,
I have problem about debugging program which for my nRF52810 custom board. I am using SEGGER IDE. I changed ses_nrf52810_Vectors.s and system_nrf52810.c files...
Hi!
We'd like to include a battery-powered remote control in our Bluetooth mesh network, i.e. we'll have a need for low power consumption.
In our mesh, devices may opt...
Hello everyone. I'm using an nRF51 with SDK 15 for a 'peripheral beacon example'. For compiling, I'm using segger embebbed studio. I have another bluetooth module(looks like...
Hello, I am trying to fabricate a board based on the Thingy design, including the accelerometer.
I positioned the components, traces, vias and pads following some recommendations...
Hi all,
Currently i am working on multilink Central and peripheral communication, now i want to do two way communication for the single central and multiple peripherals...
I am trying to use the sdk_config.h file from SDK15 to setup a custom board with a nRF52832. The nRF5283 connects to three SPI peripherals. For ease of software development...
Hi. I'm using nRF52832 SDK 13.0.0 as peripheral.
My device can be always connected by any central.
So some centrals may continue to attempt to connect to my device. I...
Hello!
I am developing a bracelet product base on nrf52832. I have a problem with softdevice's power consumption , when softdevice enabled,the power comsuption will rise...
Hello,
I am developing a basic application on the nrf52832. I am using the SDK14.2 and freertos (two very basic task).
I basically have a problem when I set a uint8...
