Hi,
I am currently building software on NRF 52810 and softdevice version is s112 7.0.1. I have one service which has three characteristics. When I add either a new service...
Device Information
Module: FANSTEL BC832 Bluetooth Low Energy 5 Micro Module
Chip: nRF52832
Firmware version: Default AT firmware
Current MAC Address: ef30:0a:cab132...
Dear Nordic Support Team,
We are currently exploring the use and potential benefits of the paEventCounter as described in the Bluetooth Core Specification 5.4, Section 4...
Hello!
Since we are moving from the prototype phase of our project to the pre-production phase, we have developed a custom board which utilizes the ISP2454, nRF54L15 SoC...
Hi,
I am working on Temperature sensor MAX30208 using nrf52840 using zephyr. i am working on ncsv3.0.0 . I want to develop a driver for max30208 . can anyone guide me how...
Hi,
I'd like to go for sysbuild with my nrf9161 based application but after some trials and errors, I am not able to find which images should be enabled in sysbuild.conf...
Hi
I am currently working with my project with 52840 and i am using sdk v3.0.1 & toolchain v3.0.0 to develope.
I am learning how to use DFU over UART from the application...
I'm connecting to the same microcontroller with nRF Master control using the same firmware, but I noticed that the connectivity time is not similar with every connection....
Hi guys,
I have a question when design the pcb layout stack with nRF52832, CSP package (CHAA). As recommendation from Nordic, using 4 layers will give best performance...
I noticed that Digi-Key had a new part number for the nRF52 DK that wasn't designated "Preview", so I assumed it might be the final silicon. However, nRFgo Studio identifies...
Now I work on designing a product, which is implemented by sending LMP commands to a bluetooth device with nrf51822. Unfortunately, nrf51822 liberary could not provide the...
Hello All
I'm newbe for this device. Now my customer asking multiple offline programming IC NRF51822-QFAC-R. But I'm not sure the device can support parallel programming...
Hello,
has anyone done some good testing on the connection quality between multiple nRF51 chipsets running on the S130 SoftDevice? (Using all four connections, 3 as Central...
I'm trying to merge 'ble_app_uart' and 'twi_sensor' example.
I developed twi function in 'twi_sensor' example. I add 'ble_app_uart' example file 'nrf_drv_twi.c'
and also...
nrf51822_sleep.txt
Currently i running nordic code in Arduino IDE through the library from RedbearLab : github.com/.../nRF51822-Arduino and I facing a problem in sleeping...
Hi, can anyone explain to me about this example in this link with details :
github.com/.../main.c
I'm a newbie in nordic and i found it difficult to understand this example...
I install
gcc-arm-none-eabi-4_9-2015q3-20150921-win32
make-3.81
coreutils-5.3.0
and setup the PATH in windows
then i enter CMD mode make some command to...
I am using the LFCLK RC oscillator, 8000ms calibration interval.
Is it possible to read from some register the resulting calibration value for the LFCLK RC oscillator?
Now I work on designing a product, which is implemented by sending LMP commands to a bluetooth device with nrf51822. Unfortunately, nrf51822 liberary could not provide the...
Hello,
measuring ADC signal on P0.26/AIN0/XL2 and P0.27/AIN1/XL1 doesn't work (I get constant value from the ADC not reflecting actual voltage on the pin). AIN2 - AIN7 seem...
I need to send a disconnect command from the app layer. I've seen a few other posts that say to use uint32_t sd_ble_gap_disconnect. One post had this line of code as an answer...
