Hello,
After I upload a new signed image to my device using MCUboot serial recovery (single image), MCUmgr Img_mgmt_client API
img_mgmt_client_state_read() always fails...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
Hi, i am learning with thingy 91 x and nrf9151dk. I made the online courses and succesfully conect to the cloud with the nrf desktop quick start in both devices. Now, i would...
Hello,
I am working with a custom board that has the nRF52840 (via the ISP1807-LR-RS module). This board has the SIT1552AI-JE-DCC-32.768E MEMS TCXO. This TCXO chip has a...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hi,
I am measuring the current during sleep, after the sequence, __WFE();__SEV();__WFE();.
With NRF_LOG_ENABLED set to 1, the current is about 486 uA. With NRF_LOG_ENABLED...
Using: nrf51822, SDK 10.
My application needs to use TWI0 and SPIS1 at the same time. However if I enable TWI0 and then SPIS1, when I run nrf_drv_spis_init() I get NRF_ERROR_INVALID_STATE...
I am working with the SDK 13 ble_app_att_mtu_throughput example. With the SDK 12 example, it seems to require the SoftDevice to be loaded with the arm5_no_packs example. The...
Hello,
I'm designing a project with the nRF52832 where I will use an external SPI ADC.
For debug and backward compatibility purposes, I also plan to use the SAADC.
The...
in the ble multilink central example i'm not understanding where the functions in client_handling.c are exercised some don't seem to be used in main or client_handling (client_handling_dm_event_handler...
I am reporting a problem that might bite you. A Waveshare NRF51822 module comes with a "Passed" sticker on the back (solder side) that makes the module stand off the mother...
Hi,
We are trying to have a thin beacon design. But we are having difficulty in finding low profile inductor for dc-dc converter matching the recommended value of 10uH...
I'd like to use Logic Analyzer in uVision 5.2 and ulink2 for analyzing variables in nrf52832.
In my understanding, I need to use SWO and configure Trace setting properly...
Hi,
I need to capture a demodulated, manchester encoded signal (16 bits long). The data rate is about 50kHz (give or take). Currently, I am configuring a PPI with timer1...
Hello,
I'm using nRF52840 which is surpport Bluetooth 5. I couldn't understand why it can do 8 X range and 2 X data rate than Bluetooth 4.2.
Besides, how to use Bluetooth...
I observe strange behavior while reading value for long characteristics.
I have characteristic 100 bytes long (read only).
In GATT client I must read value with subsequent...
can i get nrf 51 beacon antenna printed on beacon kit. its semicircular in shape... can any one help me
i want eagle library of the antenna
please help
Hi,
I want to reduce the current both in the TX mode
and in the system on idle mode as much as possible.
I measured the current consumption of nRF52DK with the original...
