I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
I have a custom board with a nRF5340 and need to configure VREGH in DC-DC mode and set 3.0V output on it.
I see the documentation on REGULATORS — Regulator control where...
Hi,
NRF54L15, nordic sdk version 2.9.1
I recently lost ability to build my application. I get this linker error:
/home/adam/ncs/toolchains/b77d8c1312/opt/zephyr-sdk...
Hello,
i think this is simple question, but nowhere i can find answer. Is nRF52840 preview development kit (PCA10056) contains built in nrf52840 microcontroller or i need...
I am going through the BLE Central tutorial and am a bit confused by the APPL_LOG function calls, from what I could understand it should give messages on serial port, like...
Hello, I have nRF51822 Beacon Kit (pca200006) and nrf51 dk board (pca100028)
I had an impression I could flash beacon and upload new files using nrf51 dk board as jlink over...
I am using IOS nRF Toolbox 4.2 DFU function on nRF51 DK PCA10028. I followed the tutorial here .
Use nRFgo Studio to erase all.
Use nRFgo Studio to program...
We have an nRF51822 peripheral device that is bonded with one and only one central. The central is always an iOS or Android phone running our app, which is scanning at "low...
In the BLE advertising library, in SDK 11, is the timeout for directed slow advertising specified in seconds, or in number of tries?
Seconds would be more consistent with...
Hi All,
I have got a project running on an nRF51422 QFAC, using the lastest SDK.
I am having some problems with the app_timers, i am able to create and start them, and...
Hello all,
i am working with the nRF52832 DK and SDK11. Actually the Enhanced Shock Burst Communication is working. I can send and receive messages. From this point on...
Lets say, that I've got a chip with program in its flash. I know I can protect it from being read back, but can I protect it from flashing anything else through debugger interface...
we have two nrf51-dks and we wanna create a ble mesh.
how can we set a ble mesh and same time ble advertising on Nrf51422 DK (PCA10028 V1.2.0) Board with using examples on...
Hello,
is there a possibility on nrf51 8.0.0 softdevice to determine whether particular notification has been received by remote device?
I use sd_ble_gatts_hvx() to send...
I am facing some problems with the app_timer api. In my application I have created two app timers. The timer api is using the swi1 interrupt for its working. I am using it...
During DFU with the nrf Connect app I get the error REMOTE DFU OPERATION FAILED. Here is the log file:
http://pastebin.com/y7hFNSBq
Using NRF5 SDK12 / NRF51 DK
...
Hi
We are very interested to test the wireless range using Bluetooth 5, 125 kbps long range mode.
If we purhase two nRF52840 Preview DK boards, is there a easy way to...
