Hi,
I am working with the nRF54L15 and I want to use it both as a BLE central and as a BLE peripheral. So, I have two separate source files: one for central and one for...
My firmware is using SDK 17.0.2, and it includes CPS, battery, and a custom service. Everything has been working fine. The custom service is responsible for sending and receiving...
Hi all,
nrf54l15dk,v3.0.1,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
Finally...
Hi,
The following URL does not include nRF54L15, is it supported?
https://docs.nordicsemi.com/bundle/ncs-3.0.0/page/nrf/samples/openthread/coap_server/README.html
...
Hello community,
I recently was trying to evaluate the GC9A01 display from waveshare, I used the github source code as the base code to test this. Attached the link below...
Hello,
I am trying to measure nRF9151 current using Power Profiler Kit II, running Cellular UDP project on EVK and following the steps in:
https://docs.nordicsemi.com...
Hello,
We are working on an NRF5340/NRF7002 based project with NCS 2.7.0 SDK. We have been able to get Amazon Root CA 1 and 3 working with the following .conf:
Now...
Hi,
Im trying to wake up from SYSTEM OFF using LPCOMP.
Im using the following code to power off:
nrf_drv_lpcomp_config_t config = NRF_DRV_LPCONF_DEFAULT_CONFIG;
...
Hi,
I am working on a Beacon application based on nRF52 DK and Eddystone protocol. So i am searching if there is already some examples/SDKs from nRF which supports both...
Looking for document or u tube to program nrf52832 using tag connect (6pin noleg) and nrf52 DK. Have the hex program and put it on the nrf582 dk. need to take to the next...
We have identified a possible transient fault condition in which a voltage in excess of VDD can be applied to an I/O of the nRF51. VDD is 3 V and the excess voltage would...
sdk_resources.h does not compile with c++ in SDK12.
The _cplusplus guard only begins if ESB_PRESENT is defined. The guard should either be moved above or below
#ifdef...
Hi,
do you have any tutorial for contiki on windows based.
no matter which platform you are using.
i am using the ecilpse with cygwin toolchain in ecilpse.
i follow...
Hi,
I'm trying to compare current consumed for different sets of commands mainly with floating point operations in them. As they execute fast, I'm putting them in a loop...
Are there any plans to add write capabilities to the NFC driver? The hardware supports it, but the library provided by Nordic does not (as far as I know). Are there any plans...
I started evaluating the nRF52 using Keil and everything worked great. However, I switched to developing in IAR because I have a full license. I'm using the same code (ble...
Hello Nordic,
I just read the news from may about the arduino primo and i am really exicted!!
I have been tring to decide between arduino due, or some complex ensemble...
I'm developing an application on a custom nRF52 board. I have no problem to program the board with Keil. However when I try to program the application with the nrfjprog, the...
Hi all,
I have been porting a project from SDK 8 to SDK12, andi have ported one of the services, however when i add a characteristic it throws
:ERROR:From File error...
Hello,
in my current project we develop a BLE firmware which runs on a custom board based on a Telit +s42 module (with integrated nRF52 SoC).
We are able to flash the...
Hi,
I am a bit confused from the example, in the specs it is said that writing the flash is word allign, and even so the example does something strange:
do
...
