Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
I am programming a Ble Nano device using Nordic SDK. So far I have been using examples from the ble_peripheral and ble_central directories. Now I want to run an example that...
Hi,
I used the nrf51822 as the spi master,it could send out the data, but it didn't receive the slave data.Did I miss somthing?
static volatile bool m_transfer_completed...
I'm working the the NRf52 dev board and SDK12.2. I was able to successfully load the standard DFU example and then use the NRF Toolbox on an android to load the example HR...
Hi.
I'm getting an nRF Dongle (PCA10031) set up on a Windows machine to be the BLE central that we'll use for our production line testing. To that end, I've built the pc...
The pc-ble-driver project uses CMake to generate Solution and Project files for the Windows build of the project. CMake uses absolute paths in these generated files. I can...
Working with nRF52832 and SD132-v2.0.1
Using Timer 1 at 1MHz (pre-scale 4) and 32bit bitmode CC to trigger events at a pretty wide range (from us to minutes).
I'm getting...
I am calling certain services and I can see this output on my UART listener:
0.000013 : UART Start!
0.385355 : BLE Stack Initialized
0.385581 : Peer Manager Initialized...
What would be the best value for UART buffer?
When I put it as 512 it gets crashes, below you can see the putty output
0.000013 : UART Start!
0.415937 : Handle list for...
I want to use app sched feature, so as example does, I call:
static void scheduler_init(void)
{
APP_SCHED_INIT(SCHED_MAX_EVENT_DATA_SIZE, SCHED_QUEUE_SIZE);
}
since...
Hi Team,
I need to make an application that we receive a data from a chip through UART and need to send the data to Console through another UART. Is it possible to make...
Hello,
My setup:
PCA10040 DK,
12.2 SDK
I copied the "BLE_APP_UART" example into my project folder and want to "upgrade" it with the TWI.
So I copied parts of the "twi_scanner...
Hi all,
I'm starting with fcc and etsi test! i know that the radio test example is useful to test the radio.But the ETSI add two type test about receive emission spur and...
Hi!
So I managed to create my custom service with one characteristic (a struct with several attribs).
I can see it in my app and everything's awesome. Yay.
But in some...
I have been experimenting with the mbed BLE Health Thermometer examples, BLE_Themometer etc. Whilst they are visible and show their name in the nRF Toolbox Health Thermometer...
