Hello,
We are working on establishing a connection between one of our existing Bluetooth modules (cypress) and nordic based module to provide backward compatibility with...
We are developing HW that includes nRF9151 running DECT NR+ with the Wirepas stack for mesh connectivity between multiple units. The product is expected to move between geographies...
Hello Nordic Support team,
I'm receiving the Transmission failure and Lora Initialisation failed message despite to correct wiring and everything else. I'd attach a link...
Hi，
Platform : nrf52840, NCS 2.7.0
I would like to get the MCUBoot image swapping progress without modify the NCS, and display a progress bar on the LCD to indicate the...
I enable cs procedure and set the procdure count equals to 3, let procedure interval to be 10.
I want to change the cs channel map between procedures. so when I send HCI_LE_CS_Set_Channel_Classification...
Hi,
I am working with the nRF54L15 and I want to use it both as a BLE central and as a BLE peripheral. So, I have two separate source files: one for central and one for...
Hi all,
nrf54l15dk,v3.0.1,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
Finally...
Hello,
I use SDK 11 with nRF52, softdevice s132.
I am able to successfully use the bootloader in serial mode (with UART) to upgrade the application, but an error occurred...
hi nordic,
After i received this kit from Mouser Electronic, when i got it check the board which some question,
we examined its outward appearance and found that this...
Hi,
I have my nrf52 DK. I would like to advertise as Beacon and be BLE (which I can connect to via iOS app) device at the same time. Do you know any examples of this kind...
Why does the macro CHECK_RAM_START_ADDR only check for C_LINK_CNT and P_LINK_CNT and not the SEC_COUNT? It is always set to 0 in the macro.
I have increased the central_sec_count...
Hi ，
I use timer to handle pwm signal,
1.when calling button by phone is pressed,
Timer starts,(function:on_key_trig_speaker_event())
2.pwm signal run (speaker_meas_timeout_handler...
Hello,
My name is krishna,
I have couple of NRF24L01+ modules,
I am trying to implement MultiCeiver in the NRF module.
The problem is i am able to receive or transmit...
Hi,
I am trying to compile the ANT Broadcast Tx Example from the latest nRF5 SDK v12.1.0 (../examples/ant/ant_broadcast/tx), but I get the following 3 error messages with...
Hi,all
I use nrf51822 connect with ios device,it will automatically disconnect when links more than 90 seconds.
device connection parameter as follow:
#define MIN_CONN_INTERVAL...
Hi I'm using the Jlink to program nRF52832_XXAA, by using nRF command V9.0.0 nrfjprog
I success in erase , but I can't program correctly,I tried Jlink version 5.12g and 6...
initially we developed code for arduino mega board but now we want to use the nRF51822 soc,so how i can utilize my arduino code for nRF51822 ....i have gone through the some...
Hi,
I'm trying to load the secure_debug bootloader for the nrf52 with the SD 132 3.0 and an aplication.
But when I load the aplication the bootloader gets erased or overwritten...
I've got a problem to change polling method to interrupt notification on open-mesh with freertos project.
The example "BLE_Gateway" of open-mesh as flow:
if (rbc_mesh_event_get...
Hi i have to use this accelerometer and connect it through i2c
www.analog.com/.../EVAL-ADXL345Z.pdf
This is my connection:
VIO --> 3.3V
GND --> GND
CS --> 3.3V...
