It is nRF54L15 + SDK 3.0 + Matter application.
I have developed a custom BLE service that is based on Nordic's proprietary NUS BLE service. The BLE custom service is enabled...
I am trying to get a WiFi project working using the nRF52840DK and nRF7002EK . I use a 3.3V power source that is supplying power to both nRF's in parallel. For the nRF7002EK...
Hi,
I'm developing firmware for the nRF52840 DK using nRF Connect SDK v2.9.2 , and I’m running into a problem that didn’t occur in v2.8.0 .
My project uses Zephyr and...
I am receiving an error when connecting to a custom board by running nrfjprog --reset, any similarly with any other commands that require connection.
I am connecting through...
We have previously used nRF52840 and for the latest iteration of our board design we are updating to use nRF54L15.
We are aware that for nRF52840 we could map any pin to...
Hi,
I faced with an initialization issue of combination two features: MCUMGR and UART_ASYNC_API. I get a crash right after the FW starts. It looks like the SW configuration...
I checked the nrf52832 manual and found that both XC1 and CX2 are analog input pins for the 32Mhz clock pin configuration. The reference design for both uses 32Mhz crystals...
Hi,
By mistake, I clicked 'fill with zero' button in Jflash, may I ask, is my chip bricked because of this? Thanks.
The following lists my steps:
program the...
Hi,
I'm trying to use the SysTick timer on nRF52 to time some various tasks for debugging. I configured it like so, which I expected would cause SysTick_Handler to be called...
I didn't find any documentation in the peer manager for the need of this write buffers.
I do understand, that peer device data is stored there before written to flash. But...
Dear Nordic,
Device: nRF51422. Protocol: ANT+. Softdevice: S210 v5.0.0
I have 3 devices: two masters (No. 1 and 2) and one slave (No. 3). In my application, I pair the...
Hi guys
I have one nrf 51822 demo board.
And I want to buy one more board as BLE sniffer.
Can I use a nrf52832 demo board as sniffer to grab packet between phone...
Hi guys
I am programming nrf51822 demo board with sdk11 and try to finish service tutorials .
I finish all step in service tutorials and try to get service information...
Hi guys
I am using SPI example code in SDK11 (./nRF5_SDK_11.0.0_89a8197\examples\peripheral\spi) with nRF51 DK.
It works fine when send first data.
But it get in...
Hello ,I work with the sdk 12, I have a program to contoler the level of battery, it works, except that I recode 3870 mV (with USB) and when I measure the pin VDD I find 2...
Hello,
I am using an Android application to send data to a nRF52 board. The nRF52 board is the peripheral and the Android phone is the central. This is the link establishment...
Hi, I am trying test nRF52840-pdk throughput.
-I loaded softdevice s140_nrf52840_5.0.0-3.alpha_softdevice.hex into nRF52840-pdk using nRFgo
-Then I build (using uVision...
Hi, the datasheet for the nRF24L0+ says that the CRC is the mandatory error detection mechanism in the packet (page 28). Being that CRC can be enabled or disabled via EN_CRC...
Is there a problem logging into Nordic site ?
I have tried resetting my password and it doesn't seem to work. Had posted a question in the this thread earlier
Dear Nordic team and community,
Have you encountered the problem where standard BT4.0/4.1 GAP Peripheral device would be "blocked" from connection (kind of "denial of service...
Just want to confirm I can be i2c master with zephyr rtos for nrf52 pca10040.
In link ( devzone.nordicsemi.com/.../) titled "nRF5x support within the Zephyr Project RTOS...