Hi. i'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
I want to make sure that how to operate DFU.
Please check there is missing point or wrong point.
Step 1...
Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi. I'm using nRF51822, SDK12.2.0, S130.
I finally compiled bootloader_secure which was very hard.
Q1. After run bootloader, I can find the device using DFU "DfuTarg"...
Hi ,
I am trying to use the new softdevice SD130 V2.0.0 and have not had any luck when using the most recent version of SD130. I ran the same application with SD130 V1...
I've nrf51dk development board. It has nrf51422QFACA10 chip and has 32kB ram and 256kB flash. I downloaded sdk V11 and programmed ble_app_beacon_s130_pca10028. It worked fine...
I try to move my project from Keil to GCC but I get some different behavior. To show the difference I use examples/ble_peripheral/ble_app_uart
The part of the code below...
I have purchased a nRF52 DK and want to use it by emulating an ANT+ Stride Based Speed and Distance (foot pod) and pair that with my Garmin FR235 running watch in order to...
Environment:
Segger Embedded Studio
nRf51 Developementkit using jLink OB firmware
S130
We're using the \nRF5_SDK_12.2.0_f012efa\examples\ble_peripheral\ble_app_template...
I'm trying to enable interrupt for radio events.
I have this code in main:
bsp_board_leds_init();
(...)
NRF_RADIO->INTENSET = 1 << RADIO_INTENSET_READY_Pos;
NRF_RADIO...
Hi!
I would like to create a RTC for stamping log messages, with 1ms resolution and including time from year to millisecond, like: YYYY-MM-DD HH:MM:SS.mmm.
What would...
Hi ,I'm trying to program Qtouch with nrf51822, and i have a question : is there any libraries i can use for my Qtouch in nrf51822 ?
i'm using QTouch :Atmel- AT42QT1070
...
I am using Nordic SDK to develop an application. I need to turn PWM off and turn it back on (to produce a beeping sound from a buzzer). To do this I went into the bsp.c file...
Hi..
I am using NRF51822 , we are using Ceramic antenna. We are thinking of designing body similar to the image. perimeter of the body is made of metal (aluminum) of thickness...
Hello
I am looking to make a program on nrf52 in which i send various values from nrf UART app on a mobile, and each value controls a LED on a GPIO. For example, sending...
Hello,
I want to combine the RTC example from the peripheral to one of the BLE peripheral examples but the problem is that the BLE peripheral examples need the softdevice...
I have troubles with logs over uart.
I'm debuging dfu bootloader secure with SDK 12.2.
BLE is used for DFU transport.
I set NRF_LOG_DEFERRED 1 as in my another application...
