Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
Hi
We are about to submit our system for BLE testing. We have been asked for RF-PHY:P9:1 RF-PHY:P9:2 RF-PHY:P10:1 values
RF-PHY:P9:1 Maximum TX packet length (MAX_TX_LENGTH...
Hello Nordic Team,
After setting connection parameters in accordance with Apple BLE design guidelines the BLE throughput has been significantly decreased.
My parameters...
Hello,
If I use the nRF51822 with 128KB ROM and I connect to a external flash via SPI.
The SoftDevice and bootloader are stored in the internal 128K ROM.
Is it possible...
Using GATT characteristic writes to transfer data is slow.Is there a cleaner and/or faster way to do faster OTA upgrade?
Also I wanted to upgrade firmware without affecting...
I have set up a 6lowpan test environment and could control the led3 and led4. could u please provide me with a code to read value at p0.01. i want to connect a temperature...
I directly connect GPIO pin with 24ohm resistor as follows.
And I set GPIO pin as high drive,
NRF_GPIO->PIN_CNF[MY_PIN_NO] |=
(GPIO_PIN_CNF_DRIVE_H0H1 << GPIO_PIN_CNF_DRIVE_Pos...
hello ,i use SDK9.0 ANCS project.when I paired it ,it can work normal. it can recive QQ,wechat,message and so on. but when I paired many times, it will be SystemReset.
...
Hi
I am trying to make an activity tracker with very low power conumption with the nrf52. The Idea is to count interrupts from an accelerometer thtat are generated if the...
Hi
I'm testing Buttonless DFU.
I use SDK 12.2.0 , NRF52 and S132.
I succeeded in entering DFU in Master Control Panel (PC application).
I want to do it even on iOS....
Hello,
I recently finished up the NRF51822 pcb board that I plan on getting printed. I posted my board before and have fixed the problems another user specified.
I used...
Hello,
is it enough to call NVIC_SystemReset() after I flashed a board so that it returns to lower power consumption? Or do I have to pull out the battery?
Marius
I hope to trigger notification from Bluetooth module into Master Control Panel. I had enabled notification/indication = true. However, when I pressed the button on my module...
Hai
i am able to store one array in flash memmory of nrf51822. but i need to save more than one set of data into flash and retrieve it separately.
how can i save more...
Hello Everyone
Is there any example code which uses indication property. Application nAn-36 uses notification property and as far as i read and understood about indication...
