I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
Hello,
I started with the UART timeslot API but countering some problems.
It will be helpful if I could get any tips or solutions.
I am trying to sample every 2ms and...
Hello
I asked a follow up question on another user's posting on devzone.nordicsemi.com/.../ , but no one seems to respond, so I will try here.
The abovementioned posting...
I've run ble-sniffer_win_1.0.1_1111_Sniffer.exe and pressed CTRL-R, then I get:
Keyboard input error: [Error 2] The system cannot find the file specified..
The log file...
Hello
I am developing an application where the data troughput is very important.
As i understand, the data thoughput is dependent on the connection interval and the number...
Dear developers,
I have a problem with peer manager reporting PM_EVT_ERROR_UNEXPECTED right after it has reported PM_EVT_CONN_SEC_SUCCEEDED.
This is quite a long call...
We all know that PPI can have the same event to trigger other tasks.
But I couldn't find any official document explaining the priorities/timing of those tasks linked to the...
Hi
I am trying to put the nrf52 device to system off state, in order to get minimal current consumption.
When I don't use the soft device, and enter system off state by...
Hi.
I'm using PCA10028, SDK10.0.0, S130.
If i scan again when it is scanning, system goes halt and reset.
So i want to check it's scanning or not before I make it scan...
We have an RFID application, the tag sends the 10 byte data and the data is read at the Receiver continuously thorough SPI channel to MCU.
Payload of 10 bytes, Enable CRC...
I've been playing around with the multi-central central/peripheral examples and I thought I would modify the peripheral to instead use a service I had written for another...
Hello, I want to detect the any activity of the ADXL 362 and blink the LED ON and it should also detect the inactivity to turn OFF the LED.I am able to generate the activity...
Hi,
We are using the Nordic Semi nRF51822-QFAA-T to do BLE project, but when we test CE/FCC RF test(Conducted / Radiated), there has a lot of noise around 2.4G.
BTW...
Hello,
I try to find the information if there is a softdevice (for nrf51 or nrf52) that supports "LE Secure Connection".
In general, where can I find which bluetooth version...
I'm lost.
Can someone point me to place or the best example of how to send data (any) from NRF51882 to iOS app when app is in background.
Is it possible at all ?
I'm trying out the ble_app_gls demo with the Nordic Master Control Panel app (on Android). What I see is that the MCP can connect to the device without bringing up a pairing...
