Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
Apparently, the dfu bootloader example in nrf51 SDK 8.1 is not working on PCA10031 type(16K RAM devices). In my case, the device is RedBearLab BLE Nano and nrf51822.
Can...
Hello,
because of my mistake, rx tx pin was not cross connected.
So i want to swap rx tx pin on nrf51822.
In the example ble_app_uart_s130_pca10028, i change the code...
I used the example in nRF51_SDK_9.0.0_2e23562\examples\dfu\experimental, the first time that work well. But when I want to update a app in app(with dfu function),it failed...
Sir,
Can someone tell me what all things I should remember while I am trying to execute a project which is developed in sdk6 to be excecuted in different sdk file(maybe...
Hi, i'm using a code to save 4 bytes on the flash memory and it works. In, fact i checked the data address concerned using the keil and i see the changes when i write and...
I can send a CR terminated string through the UART using tx fifo OK.
BUT, if I receive a string from the UART rx OK first, and then try to send a string, only the 1st character...
Canyou please tell me how to do , to save correctly 4 bytes in my program that uses flash memory for bonfing. i have how to save 4 bytes function seperatly, and my program...
Ported the hrs_rscs relay central-peripheral app with peer mgr to custom platform with mutliple peripheral devices, and it has been working very well. The last step is to...
Hi,
I have a app that using a constantly blinking LED started at power-up, however I am having some trouble stopping the timer.. (Yes, I know it's simple.. but i still...
Dear support team,
I have problem with recovering the nrf52dk board.I check devzone.nordicsemi.com for issue, but nothing solve the problem. Board need to be recoverd...
I want to use nrf52832 to communicate with my sensors , but my three sensors should use spis to communicate, the others use TWI ,so in sampling , I need to switch between...
Is there a schedule to release an up to date version of the "nrf51-ble-driver_win_0.5.0" package, including the compiled serialization dll?
The package is a download for...
Hi,
I am burning the same code on two sets of chips nrf51882 and nrf51442. The nrf51882 chip is with 16kb RAM and 128kb of flash memory while the nrf51442 chip is with...
Hi,
I took a example (ble Peripheral : ble_app_uart) and enabled bonding and whitelist as per the tutorial devzone.nordicsemi.com/.../ and followed these link ( devzone.nordicsemi...
Hi. I'm using SDK 11, SD s130, gcc, nRF51822. My application is a peripheral that advertises OK and gets a connection from our mobile app OK, but then gets a PM_EVT_ERROR_UNEXPECTED...
