I have been testing the thingy91x and measuring power consumption trying to reduce it to the absolute minimum.
Using a test program that moslty sleeps ( using k_sleep()...
Hello,
I'm working on a project using the nRF52840 and Zephyr, and I'm experiencing an issue when trying to use device power management (PM) with a custom sensor driver...
I am trying to get the wifi stack to connect to a wifi AP using WAP2 Enterprise (initially just with identity and eap_password, later with full ca_certificate check and client...
I've got some timing-issues with the nPM2100. As I could not locate the relevant information in the datasheet, I'm requesting this here.
My PCB has an nPM2100 with a mechanical...
Hello
I’m aware that this topic has been discussed in several posts from a couple of years ago, but I haven’t found a concrete solution yet.
I'm currently using an external...
When my peripheral calls sd_ble_gap_phy_update, setting rx_phys and tx_phys to BLE_GAP_PHY_AUTO, I receive the BLE_GAP_EVT_PHY_UPDATE event with a status of BLE_HCI_UNSUPPORTED_REMOTE_FEATURE...
Hi,
I recently checked support of MCUBoot validation and from NSIB for nrf54l15. (sdk 3.0.0 and above)
During this, I enabled Signature algo as ecdsa-p256.
And...
Hi!I work with a Beacon Kit (nrf51822) and I would like to know which is its default radio transmit power and the velocity of transmission. In my application I sent via Ble...
Hi,
I'm using the reference project "Experimental: Eddystone Beacon Application" to transmit Eddystone URL packets and I'm sniffing the data with Wireshark.
I noticed...
Hi,
I'm using nrf51822 board with SDK 10 and S110 softdevice.
My application is based on uart over ble. It take 20 bytes data from a android device using nus, store that...
I have created files before with s110 sd8 with the
nrfutil.exe utility using a bat file.
nrfutil.exe dfu genpkg --application nrf51422_xxac_s110.hex --application-version...
Hello,
I want to connect one board trough SPI to my nRF51-DK. Using SDK11 and SD130, the nRF51-DK is the SPI master, I call the function nrf_drv_spi_transfer() but the...
Hi ,
In my project , i can use the battery service in my project.
But if i want to use the another four ADC channels , how to add it ?
my project is working at SDK 9...
Hi,
I am using 2 nRF52832, one for ESB Tx and one for ESB Rx used to send payload through UART using SDK11.
Tx board is used has a low power transmitter which transmit...
hi all,
i am a begineer to nordic. i want to send data over ble and read that using master control pannel.
please say wat api i want to use and how to use. please give detail...
Hello I'm new of nRF seriese.
nRF51822CEAAD00(0x004d)
SD130 ver2.0.1
kail Ver5.18
SDK11.0.0
I just finished the tutorial and now I'm making my new project with twi...
Hi, I am using Heart Rate rate monitor code to send floating value instead of unit16_t.
I am using the heart rate service to send the data. Instead of using simulated sensor...
Hi,
I am new to nRF5x BLE devices.
I need to create a project and would like you to help me out.
I need to connect two nRF51822 devices. If one of the devices goes...
hi dear officers
since the datasheet states that value 1 stand for connected, does it mean this pin is active-low.
in order to physically reset the device, could i connect...
I have tried ble_app_uart_c project in SDk 9 , SDK 10 or SDK11 , but they have the same problem.
Problem is that slave(SDk 9,ble_app_uart) can send data to master(by terminal...
While trying to bond an iPhone 6 (running nRF MCP App) with an nRF52 with S132 2.0.0 I encountered the following error:
On the first try, when the iPhone is not yet paired...
