But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hi,
I have done BLE tutorials [BLE Advertising, Ble Services and BLE Characteristics]
With my NRF51-DK was working perfectly the example of BLE Characteristics (with...
Hi,
I designed a pcb using nrf51 chip with some sensors,
this pcb should read ,every minutes, all values from sensors and saves them into the flash memory beside that...
Dear
Now, I need make one nrf52832 board as USB Dongle, it can be HID device by checked from PC.
And, nrf52832 should support esb protocol, now for esb, I know something...
hai
i was started a bluetooth based project. So i have started with a blend micro.But the range of communication was very short.So i have chosen ble nano with TX power...
Hi
I am calculating the power consumption using
devzone.nordicsemi.com/.../
But there is some point that I don't understand.
When the BLE event type is "Peripheral...
Hello,
the past week I am trying to make the bootloader_secure example work for a custom hardware with no luck. This whole procedure give birth however to several questions...
Hi
I am currently working on a BLE based hardware but I am a little confused about the terms such as service, characteristics... etc.
Let's say, I would like to control...
Hi,
I am using the following function to read the content of a register:
static ret_code_t read_reg(uint8_t slave_address, uint8_t register_address, uint8_t *value)...
Hi,
Could you please help me identify the file and function name that is used by the S130 softdevice to start HF clock automatically for ble advertising? I can see that Clock...
Hello again,
I'm working with the ble_app_hrs example application with DFU app support. I'm following the DFU procedure and I've reached the point where I actually start...
Hi everyone,
My idea is:
I have several nrf51822 ble devices and I want to connect them simultaneously one by one with gateway over IOT. I am using bluz gateway shield...
hi all,
I use nRF52 SDK11 with ble_app_beacon example.And write some code in main().
uint8_t buf_data[32];
unsigned char c_data[] = {"abcd"};
//unsigned char c_data...
When debugging my application, I'm finding that gdb blocks at app_scheduler.c:253 like this:
(gdb) bt full
#0 0xfffffffe in ?? ()
No symbol table info available.
#1...
I'm using SDK 12.1.0, gcc, nRF51822, no SD init'ed or enabled at the time this code is running. I need to retain the values of a bunch of variables across a sys off.
Here...