Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I'm trying to write a test service on a PCA10001 that transmits a single scalar value that is computed from a few different sensor readings. I would like this service to send...
Hi everyone,
I have an interesting problem loading the S110 SoftDevice. First, loading version 6.0.0 onto the Evaluation Kit using nRFgo Studio works fine. However, loading...
hey,
I am new to eval kit and i am asking a very basic question, i want to send the RSSI from PCA10001 board to usb dongle PCA10000.i am looking the examples in sdk for this...
I'm seeing periodic disconnects with an iOS client application and the NRF_ERROR_SVC_HANDLER_MISSING which I gather may mean there is a compatibility problem with SDK and...
I try to use nrf51-ble-app-lbs with softdevice 7.0
I download ble-app-lbs at github.com/.../nrf51-ble-app-lbs
And change IROM1 start at 0x16000 lenth 0x29000.
...
Hi
wil it be possible for you to compile gzll_iar.a for SDK_v5.2.0.39364 ?
I have an aplication running whre I need gazell functionallity; and I have trouble converting...
When I would like to change advertising interval, should I execute sd_ble_gap_adv_stop & sd_ble_gap_adv_start again?
Is there any way to update its interval without stopping...
We will be using nRF51422 with S310 SoftDevice for our development.
ANT for mesh network implementation as that's what it does best, and BLE for interfacing with mobile devices...
Hi,
maybe i have a silly question, but i didn't programm timers before. I know how they work. But how is it possible that there are only three Timers in the 51822 and so...
hello
I am a BEE undergrad student currently doing a project using the nrf51822 Eval-kit.
If you could help with a simple transmitting code. I have to take data from a sensor...
Hi,
I uploaded the app to the kit as I have been doing it for the last 2 months and from now there is no way to get back to advertising mode. Before, I used the nRF Master...
my purpose is like that:i want to collect some useful data from external sensors before initial BLE ,and when the the nrf51822 advertising,i send this data out to the smartphone...
Hi,
I am trying to use the PCA10004 board in a custom application without the use of starter kit.
When I burn the nRF51822 chip with my custom program, in my custom hardware...
