Hi,
I am getting randomly incorrect SOC reported by pmic npm1300. For most days, it reports correct SOC but then all of a sudden it starts to report incorrect SOC even though...
Hi,
I recently found out about the Periodic interval feature on GRTC CC[0] and it seems like it would be quite useful for my application. Most of my code so far uses the...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
I'm trying to implement a fall detection feature on the headset side using the LSM6DSOX IMU sensor. The IMU is configured successfully, but the board halts after the INT1...
I have a ready hogp struct and I'm trying to subscribe to an input notification (I'm connecting to a bluetooth keyboard) and I'm getting error -22. Here's the callback in...
Hello,
I am trying to count pulses on nRF52840 DK's pin for measuring water flow with hall effect sensor. I tried to implement PPI + GPIOTE + TIMER in counter mode, but...
Hi, I am using nrf52840-based custom hardware and have an external flash connected on SPIM3. Till now I was working with my other peripheral connected on different buses and...
How to make BLE examples working. for nRF52DK series (BLE_app_template)?
Hi, I tried for around a week. and I will describe what I did, and what I have found first.
I...
We have IoT gadget, where we use coin cell (CR2032) as power supply. Now, we would like to connect U_bat directly to ADC to measure battery level every n minutes, but keep...
Hi.
I have an NRF52DK Board. With the built in JLINK Debugger it works fine. Now i bougt an KEIL ULINKpro Debugger. Is connected with the 10 Pin cable. And i cannot flash...
Hello.
I'm working this : github.com/.../pc-ble-driver
In Chapter: Compiling the connectivity .hex files
2.Apply the patch hex/sd_api_v/SDK_connectivity.patch from...
Hi!
I have 2 nRF52 custom designed PCB. Is it possible to develop android app that connect both nRF52 PCB at the same time and receive the data from them at the same time...
I keep having problems like frequent disconnects (reason 0x08 = BLE_HCI_CONNECTION_TIMEOUT) and NRF_FAULT_ID_SD_ASSERT on my NRF52832 (tested with S132 v3.1.0 and V5.0.0-alpha1...
In the API file nrf_drv_twis.h for the nRF SDK, the definition of NRF_DRV_TWIS_DEFAULT_CONFIG looks interesting. The definitions for SCL and SDA pins are both set to the same...
Hello,
Is it possible to have 170 characters long device name somehow to the nRF52832 so that standard Android phones are able to see it without any pairing or any other...
In ANCS example (SDK 11.0.0)
I thought keys list distributed should be the same naturally until I see the code below.
ret_code_t dm_register( dm_application_instance_t...
I saw following code configuring about permission of charateristic value R/W.
it's in uart example of SDK 11.0.0.
static uint32_t tx_char_add (ble_nus_t * p_nus, const...
Hello
could anyone help me how to setup pipes for my characteristic, i need to recieve/transmit data to UUID of my characteristic, and recieve/trasmit to ClientcharacteristicConfiguration...
I have a ADC interrupt that occurs every 17ms and which copies the samples into a global static array, after which GivesFromISR to a binary semaphore so that the samples may...
please anyone answer for how to configure the digital input to make active the digital output in nrf52832? if give example program means it is much better
Hey!
I am working on NRF51822-QFAC, with the help of SDK 12.2 with the aim of scanning my bluetooth speakers and mobile phone.
For the same, I have loaded the project...
