Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
I have a strange behavior with the Timers. For my project I use a Raytac module with a nRF52 Chip on it. Softdevice is not flashed. Project is based on SDK 11.0
When I...
My setup:
NRF52DK;
Keil 5.22.0.0;
nRF5_SDK_12.2.0;
S132 3.1.0
While trying to use ble_peripheral\ble_app_template\pca10040\s132\arm5_no_packs I decided to modify...
I'm sorry. I closed this question and can't reopen. I need more answer.
If I solve all problem I'll close this question.
As you mentioned I'll try HW version modification...
I've just noticed that it's possible to call ble_advertising_init() and ble_advertising_start() with params that are quite conflicting.
ble_adv_modes_config_t advertising_modes_config...
Hi dear Engineers!
We want to add Eddystone compatibility to the device.
Is it possible use nRF52 silicon radio ?
How I understand, it is not compatible with any SDxxx...
After a few minutes of running, the Power Profiling kit will start printing out "Range not detected" messages in the console. It appears to be related with the "Average" window...
Hi,
I am using mca8652fc and used device address as #define ACCELEROMETER_ADDR 0x1D
but it is not reading WHO_AM_I register properly.
I used #define ACCELEROMETER_ADDR...
I did try SPI interface between nRF52-DK and MAXIM11300.
Unfortunately, I did not successfully it work.
I used SDK_11.0.0 on nRF52-DK 0.9(Engineering B) and that
...
Hello, according to devzone.nordicsemi.com/.../ it was an example in nrf51 sdk 6.1.0. I checked it and found no files or folders related, not in sdk 6.0.0 or sdk 7.0.0 Could...
Hi,
I need to send my packets with an interval smaller than 100ms in unconnectable mode. I know, that this is a restriction from Bluetooth standard. For my application...
Hello,
I've a problem with handling interruption on nrf51dk (SDK12.1.0).
I set GPIOTE to handle interruption based on the example code "pin_change_int".
I work with the...
I am trying to use the NRF51 soft device with the App_PWM library. I can get both working individually, but when I try to enable both, I can no longer connect to the device...
