I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
When you download win driver (from www.nordicsemi.com/.../72324929 for instance). There's only a win32 dll/lib provided.
However, modern development are often made on 64bits...
hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi, I got the DFU modify to use Synthesize clock (NRF_CLOCK_LFCLKSRC_SYNTH_250_PPM) working with SD7 and SDK6. Tested on a board with the 32 KHz crystal, everything works...
Dear Sir/Madam,
One of our customer is using nRF51822 in the design and Proto has been completed. Customer is looking for the followings.
What all certifications...
Hello:
When I use Android 4.3 to connect nRf51822 AKII board, HEART RATE always show error on discovering services(129, then I can't connect nRf51822 AKII board.
Does...
Hello,
i want to develop open source software for nRF51 but i think the SDK licensing is to restrictive. I cannot use any of provided example code because its permits redistribution...
This is my code snippet
int main(void)
{
uint32_t err_code;
...
// Scheduler
scheduler_init();
// Initialize the SoftDevice handler module.
SOFTDEVICE_HANDLER_INIT...
Hello,
I was working over nordic dev board and found the uart template. but in that, only "data_receive_handler" is mentioned. i want to send data from my dev board to...
Hi All,
I am working in the sleep mode with system off and wake up with internal RC RTC.
It function well when connected to EV board...
I see the "Emulated System OFF...
Hi all,
I'm using the nRF51822-EK (PCA10001) and I'm going to develop a bluetooth cadence (and speed) sensor for MTBs.
I desire low power consumption and i though to put...
hiii...
I was working on ble_app_hrs example of sdk-6 using sd7.0.0. I tried to add broadcast feature by sending some hex values, dat was working, but now i want to display...
Hi,
I need to use 2 TWI bus (hardware constraint) so I wish to drive one bus with twi_hw_master.c and an other with twi_sw_master.c.
Each bus have their own GPIO.
...
Hello.
I'm reading the nrf51 Reference Manual.
in MPU section, [ (SWD) will no longer have access to code region 0 or code region 1, as well as no longer being able to...
Hello,
downloading the file nrfgo_sdk_2.3.0_setup.exe causes the virus scanner to report an issue and moving the file into a restricted zone.
Can you help on this...
hi, i made ble app with nRF51822 (s110), sdk 6.1.0
and i put this code after a pstorage_store() function to wait finishing of this function.
uint32_t err_code, count;...
My board is nrf51822.
Simple_uart works fine in uart_example, but once I copy it to my ble project which can work, it stuck.
Part of my code :
advertising_init();
services_init...
Hi all,
Now I'm using the nRF51822 DK and nRF Loader APP do the OTA.I can use the APP to complete the firmware update.However,the device
cann't go back to bootloader mode...
