I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
What does error code 4 mean?
I am looking through the documentation for the error code number to string translation.
Why is starting a timer causing the error code 4?...
I am trying to sample the ADC every 2ms. I notice lots of slowness with BLE advertising and typically can't connect to device over BLE when sampling. I am using PPI, configuring...
Hi
I'm trying to run the HRM_RX exemple on the nordic NRF51422. This is my configuration:
-Eclipse IDE
-ARM GCC 4.8.3
-NRF51422_AAC0 so I'm using the lasest SDK 4...
hello,
i am trying to use the example for the ble_lbs from github.
I get no erros on compile and flashing.
But wenn i try to see the device in the master control panel...
I've been slowly and incrementally adding changes to the ble_app_multilink_central example from nRF51-SDK-6.0.0. This is an exercise to understand where my other app stopped...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Hello everyone!
Firs of all consider I'm very new in micro controllers programming/debugging, so your patience would be much appreciated.
I have a nRF51822 mKit like...
I use multilink_central example and try get information about discivered service:
APPL_LOG("[CLIENT_LOG]: Count of services: %d\r\n", p_client->srv_db.srv_count);
APPL_LOG...
my led connect whit a pin like this:
the led positive connect whit VCC and the negative connect whit a pin through a resistors.
when I config the pin as a output like...
using the nrfGoStudio to program s110_nrf51822_6.0.0_softdevice.hex
Tools:
Jlink,SWD mode as the figure:
but there are some problem
1:we can download demo BlinkLed...
Hi,
I need a RTC calendar ble stack on nrf51822 .
(turn on the RTC0 on ble stack and get the count, how to setting the rtc wakeup )
which calendar need follow :
track...
Hi,
I'm trying to get a time stamp using that kit, but I'm having problems doing it because always I upload the code to the kit, it stops working.
I add here the code...
