Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
Hi,
I would like to use Random number generator when soft device enabled. I have seen random generator example, but I can not use the same when soft device is enabled....
I was considering the following possibility, using an nrf51882 module or another module to receive ble advertisements. I'm pretty sure this is possible. Using the internel...
please, help me ㅠ_ㅠ
it mades me crazy
My PC is Windows 8.1 & 64 bit.
I try to install / repair / change SDK (6.1.0 version, 6.0.0 version, 4.4.1 version)...
I have achieved the demo referring to the IoT SDK and can control the lights on the nRF51 DK through the Firefox browser with Copper plgu-in in the LAN.Recently I want to...
Hi,
I interested in a simple system of a master and slave nrf2460. But how many of these systems would happily coexist in a the same room?
Thanks
Senthil
The Enhanced ShockBurst PTX Project just inits the ESB and start transmitting without ever configing either of the 16MHz or 32kHz clocks (none that I can see at least).
...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
hi.I have a question about synchronization. In main loop, there is a function sd_app_event_wait() which blocks until ble event from softdevice call occurs, so I want to put...
Thought I'd check to see if there were any examples floating around that demonstrate how to dynamically claim memory when the softdevice (s110) is disabled? Any hidden gotchas...
Hi All,
We have embedded windows ce devices, and were thinking of adding ble functionality by connecting a small nrf51822 board through a serial port.
Would it be possible...
I'm currently debugging a daughter card for the nRF8122 evaluation board but there's a higher voltage and current on that daughter card.
I want to know how the IO are connected...
We are developing an application based on S130 V0.9 (orignially S130 V0.5 was used) SoftDevice using development boards PCA10001/PCA10000/Beacon. Main activities of the application...
Hi,
I am trying to use the spi_slave_example on my nordic nrf51822. But i have an issue :
I can build all target and download code to flash memory but nothing happen...
Hello,
What is he meaning of PROTENSET0, PROTENSET1 in sd_flash_protect()?
How can I use this function to set WRITE PROTECT to a certain flash page?
I searched a lot...
