Hi
I am trying to setup and test the OpenThread CSL feature on nrf52840DK with OpenThread daemon and RCP mode nrf52840DK.
I found there is a way to build the Daemon for...
Hi,
With several nrf52840 based prototypes, I had serious problems. I could see them die after flasing them a few times. And this was not just one dying, it was all of them...
hello all,
I'm fairly new to nRF SDF and its build environment. I browsed a lot of posts but did not find the solution to what is probably a basic misconfiguration error...
Is a common ground required when measuring current in current meter way?
Can externally supplied voltage exceed 5V? Will this cause inaccurate test results?
I'm working with nRF5340 and nRF Connect SDK 2.9.0, using sysbuild and Partition Manager for my project. I want to enable Zephyr's coredump feature and store dumps in internal...
I have a custom NRF9151 board with Windbond W25Q32JV flash, and some other peripherals connected. It also has GPS and LTE which I have tested and work. My UART console is...
Hi there, I am unable to install an SDK through VSCode while trying to take the steps outlined in the documentation. I have navigated to "Manage SDKs" under the "nRF Connect...
Hello,
In previous version of SDK, I used to use "sd_nvic_systemreset()" function to reset nRF52, but this function disappeared in SDK12.2.0 .
The question is what the...
Hello,
I am receiving the above error on Android BLE app while connecting to my pca10040 based board, and I developed this app with nRF Toolbox as a reference.
I am...
Hi all,
I have understood that sys_evt_dispatch is used for all events that aren't BLE but concern the softdevice.
I start to develop my code on gls_example, here in...
I have an application where I need to synchronize several devices to within 1us using a radio. In order to do this, we need to make a protocol that allows precise synchronization...
We have these Dev Kit Nrf52 and also Nrf51 Bluetooth Smart Beacon Kit. For our application and for the simplest user experience we would like to benefit from update via OTA...
My product only offer a debug interface（SWDIO/REST，SWDCLK，+3.3v，GND），but I learn that the nRF51 DK debug out interface has several pins，such as EXT VTG，EXT GND DETECT，EXT...
hi all:
I am a new user.Now i have a project in which I need to implement a function a host and four devices .I just want to know if i use the example of " gzp_dynamic_pairing...
Is a delay needed between Characteristic updates
I modified the ble_sdk_app_proximity example.
I added x3 services, based on the BLE Characteristics, a beginner's tutorial...
I have 32-bit float numbers, sent to the BLE from SPI.
I can manipulate this into x4 bytes, or actually use sprintf and get a real 6-byte representation of the number.
...
I have taken ble_app_ancs_c_s130_pca10028 example and modified the application to run on our custom board.
The custom board uses NRF51822 (NRF51 IC revision 3).
The following...
Hi,
We are using nRF51822_QFAB (128K/16K), S110 V8.0.0 and SDK V10.0.0 for my development. We are in the need of guest (unbonded), pairing and bonded mode.
Guest...
Hello,
I'm struggling with setting up the eclipse IDE to build the blincky program in the SDK now I've configured all the paths and eclipse configuration according to this...
Hi ,
I am using nrf5 SDK v12.2.0 ,
I have an nrf51822 board .. can I just compile the examples in SDK for pca10031 and use it for nrf51822 . Please let me know what I...
