I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
I have downloaded the nRF51 SDK from here www.nordicsemi.com/.../nRF51822 and I'm trying to run HCI-UART examples as explained here developer.nordicsemi.com/.../a00063.html...
Hello,
I use SDK 13 on nRF52832 with a SD card (nRF port of fatfs lib).
I have a long sleep and i want to minimise current.
With SD card, it's okay i switch off SD...
Originally, this was a complaint about SIGTRAP 0xffffffe while using GDB.
But I've discovered the actual issue is related to a lack of erase/programming of FLASH.
My environment...
I would like to know how long is the minimum pulse width for SENSE to trigger GPIOTE Interrupt from external pins on NRF52832,I have seen
devzone.nordicsemi.com/.../
How...
Hi,
What is the status of a MISO pin of an SPI instance after issuing NRF_GPIO->IN? Does it reflect the real state of the pin? If no, what fast options do I have to read...
hello ,
i have a question, when i download the application.the power dissipation is more than 1mA, and i press the reset key to let the reset pin low level,but it is not...
I have an application that first reads ADC sensor data from a SPI device, then transmits out through BLE. I have a 4ms timer; once it times out
Read sensor data through...
Hello,
I would like to ask your help for examples of nRF52 code, when entering and exiting critical regions (disabling interrupts without switching off a bluetooth connection...
Hey,
just wondering if its possible to lower the pwm driver clock of the nRF52832 to around 500Hz? Im working on a LED dimming application and the LED spots i use have...
Hi,
I got a error fatal awhile after the app switched to low advertising.
Could you please tell me where I can to look into ?
I got the error code 8198 from sd_power_systemoff...
Hi everybody,
Chip: nRF51422
Board: PCA10028
Firmware: S130_nRF51_2.0.1
I found it really difficult to write DMP driver for nRF51.
I've already downloaded motion_driver_6...
Hi,
I have been modifying the MQTT Publish example for a product and found that the PUBACK message does not produce an event. The problem is in components/iot/mqtt/mqtt_transport...
I am trying to start development on the nRF52 Dev board PCA10040. However after updating to the latest nRFgo Studio 1.21.2, I cannot seem to program the board. I'm simply...
