I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
In the product specification page 165, I see than the continuos mode is 2 to 16kbps. In the page 167 this mode is 2 to 16ksps.
Which unit is correct, kbps or ksps?
If...
Recently I have put some code of my application into RAM. When I do not enable read back protection mechanism everything works, however when I want to enable protecting my...
Hi all,
I have updated a custom automotive PCB and am now using the nRF51824 instead of the nRF52832 I had been using previously.
Unfortunately, I have been unable to...
I am very excited about the Bluetooth 5 LR PHY, but do you plan to release an update to the nRF5 SDK to support the newest soft device S140 v5.0.0-3.alpha?
Hello
I am new to work on nrf52,
Please can someone help me regarding how to use hardware and software pwm together. I have a need of using 13 leds , so i need 13 pwm...
Please can anyone help me on how to use(program) PWM hardware with individual loading mode? My goal is to control 12 LEDs individually with different duty cycles and playbacks...
I want measure the current of a device over a resistor. It is connected to 5V which is over VDD(3V) of nRF52 Chip.
5V--->10ohm--->Device
the differential voltage of this...
Hi,
I am using SDK v8.0.0 , Softdevice s110 and Example is ble_app_uart(peripheral).
i want to reduce a range of nRF51822 beacon(PCA20006) up to 2-3meter..
i try this...
Hi all,
Basically I am doing an exercise on the BLE system use case. Let's say I want to setup a BLE system where there are the long range BLE capabilities in Relays and...
What is a minimal length of preamble, such that nRF51 is able to safely receive a packet with? Can it be made (via some magic registers) to be as small as 4 bits? Then it...
Hello!
I'm pretty new to BLE and Nordic, and hope that someone can give me some good advice.
I'm working on a project were I have 2-4 sensors, each connected to a nRF52832...
Morning,
I ve try to flash the hex pca10040 from the examples/ble_peripheral/ble_app_hrs without success, with the flash seems ok, i can t see the device.
So as i ve...
I found this comment in fds.h as function header for fds_record_write()
* Record data can consist of multiple chunks. The data must be aligned to a 4 byte boundary, and...
