In Electrical specification Table 1 (current consumption in forced High Power mode) lists a typical value of 7.2 mA , just want to confirmed this is correct and not a typo...
Hello, I am developing my custom board using Thingy53 as a reference design. I am trying to achieve DFU from application using external flash for the secondary image and upload...
Hi, we are developping a medical device that receives an audio stream from a smartphone. We have a custom board connected to a different DSP than the one in the nrf5340_audio_DK...
Hi! We're testing nRF7002 with the nRF7002-DK and NCS v3.0.2. CONFIG_NET_ZPERF=y has been added to the nrf/samples/wifi/shell/prj.conf, the rest is untouched. Running that...
I am using the nrf5340 on a nrf7002fk dev kit. I am interested in low power operation so I am measuring the power consumed.
I am running a simple app:
int main(void) ...
Hi,
I have a simple question about Bluetooth Channel Sounding:
Question: If I use BT_CONN_LE_CS_MAIN_MODE_3 as main mode (PBR + RTT), does it make sense to use sub mode...
Hello Nordic Team,
I am currently working with the NRF54L15-DK. I have successfully configured the simple ADC on AIN4 (P1.11) and am able to read the raw sensor values....
According to the data sheet for the nRF51822 the channel range is from 2.400 - 2.483 GHz.
In the radio test example however, it limits the range of test channels to 2.400...
Has anyone been able to get Eclipse working with the pure-gcc makefiles and autodiscovery of include files?
I can get Eclipse to build my project using the pure-gcc makefiles...
Hi,
I am using the nRF905.
Got a transmitter and receiver working.
Problem is the receiver only accepts packets of 32 bytes in size. As soon as I send smaller packets...
Hello,
once synchronized, what is the minimum time for exchanging acknowledged packet.
according to datasheet :
Timeslot periods
The Gazell Link Layer supports...
I've setup Eclipse GCC tools for building and debugging as per the nAN-29 app note (and lot of online help) and able to build the code. However, the debugging is working only...
I'm new in nordic.
I want to use nRF51822 as an iBeacon for iOS.
This is possible?
There is an example, documentation for this ?
I have nRF51822 BLUTOOTH SMART BEACON...
I'm interested in working off the reference design for the nrf51822 to create my own board. I have a few questions about the 3 inductors specified on the schematic/BOM:
...
hi,
I an trying to enable notification from server. According to spec. i have to write 0x01 to the CCCD handle in heart rate characteristic in ble_app_hrs. In the BLE_GATTS_EVT_WRITE...
hi everyone
(1) everytime,the pstorage_init get the same block id, if we wrtie it more than 20,000 times , will this block become a bad one? if it will, can the program automatically...
Hi, Ole
I am using Nordic development board with Nordic dongle to communicate,..but I am getting receive link loss. I have removed reset from error handler, though the...
I have a setup where I will be switching the nRF51822 UART between two different peripherals (one being a connection to another nRF51822), so I need to be able to safely close...
Folks,
Sorry if I'm just being boneheaded here, but have been fighting with a couple problems while migrating my app on nRF51822/"C0"/SDK 4.2.2/S110 5 to nRF51822/"G0"...
We have made a custom board using nRF51822 connected to a MPU6050 accelerometer running on a battery.
Currently, we have issues performing reset on the chip. We have to...
Hi
I'm trying to measure the frequency of a pulse signal that runs at a moderate pace, varying between 50 and 500Hz while the SoftDevice is active. The softdevice needs...
