Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hi. I'm using nRF52832, SDK13.0.0, S132.
When I make bootloader, I should make *.setting file for application.
Do i need *.setting file when I update just application...
Hi,
this is not a question about the nRF but about Android programming. Hope some of you can help me anyways. I modified the android part of the nRF Blinky example github...
Hi Nordic Team,
I saw some issue with Nrf connect on IOS.
First the App crash when i open it.
Second with IOS i can see some issue with pairing and bonding...
Hello,
I intended to implement an application without OS. Due to safety concerns I would like to have two call stacks : one for softdevice using MSP and the other for my...
After programming the Ble_app_uart to the nrf52832, I am sending a 100 Bytes of data from my UART Port to Nordic chip and this data is transferred over BLE to my Phone. I...
According to Table 19 in the nRF24L01+ datasheet, writing to any of the 32 command registers is "Executable in power down or standby modes only". This caveat is also repeated...
Basically I want to get a 8 byte long MIC when using the AES CCM encryption. From the product specification it does seem like I can only get a 4 byte MIC, is that correct...
Hello,
I try to flash my dev card nrf52 with the program ble_app_uart
Or a program ble by cons I can flasher by other program (pin change in), I do not know from where the...
I created an characteristic that has MAX_Length = 20 Bytes characteristic.
And When I'm trying to write less than 20bytes on this Characteristic, It Always send with 20Bytes...
Is it OK to send multiple packet continuously over nus at below way without waiting for packet transmit complete?
i=UserUart.RxBuf[1]+2;
index = 0;
while(i>0)
{...
Hi,
I'm using nrf51822 Ek kit and running ble_app_uart example,when i want to send any character or integer it Received like a string only,but i want to send only single...
Hi,
this question is more about iOS than nRF, but there's probably here some experience around this subject.
First the context : We have a product based on nRF51, S110...
I compile a .bin file for DFU. The bin file is 62020 bytes. I create the zip file for DFU, it is 62909 bytes.
If I extract the zip file, I get the bin file (62020 bytes...
We are currently designing a prototype board for our product using the nRF52832. We need to calculate the transmission line with on a 4 layer PCB. The stack-up looks like...
