I have been testing the thingy91x and measuring power consumption trying to reduce it to the absolute minimum.
Using a test program that moslty sleeps ( using k_sleep()...
Hello,
I'm working on a project using the nRF52840 and Zephyr, and I'm experiencing an issue when trying to use device power management (PM) with a custom sensor driver...
Hello,
I am new to nRF development. I am going through the nRF Connect SDK Fundamentals course.
I wanted to configure a GPIO on the nRF52833 DK board as an output and...
It seems that I'm getting different results reading QSPI flash from the APP vs MCUBOOT, with the exact same configuration. Writes appear to work fine from either, but MCUBOOT...
I am trying to get the wifi stack to connect to a wifi AP using WAP2 Enterprise (initially just with identity and eap_password, later with full ca_certificate check and client...
I've got some timing-issues with the nPM2100. As I could not locate the relevant information in the datasheet, I'm requesting this here.
My PCB has an nPM2100 with a mechanical...
Hi,
i acheived writting code that reconnects sequentially with multiple reflectors for my 1 initiator. When i am indoor i had good results, but yesterday i tried it with...
Hi,
I am a new comer to the nRF8001.
I am using Redbear Blendmicro (nRF8001) for my project.
I have wrote a apps to scan my Blendmicro(s) and acquire their RSSI value...
I use direct input AIN2 pin battery 3.3v, the other pins are not connected to anything, I did not enter into ADC_IRQHandler,may ask about what the problem it
this is my...
Has anything changed with the Bluetooth LE in iOS 8? I have an ANCS library for Arduino ( https://github.com/robotastic/ANCS-Library ) that was working fine with iOS 7. I...
I'm trying to program nrf51822 via st-link and open ocd.
Here command:
openocd-0.8.0.exe -f interface/stlink-v2.cfg -f target/nrf51_stlink.tcl -c "program address".
...
dear all:
I have 2 kind of board that are PCA10006 and PCA10028,
but I find out the IoT example can't be run on PCA1006,
what are different between PCA10006 and PCA10028...
I have added the DFU service to our own project. Normal application updates work perfectly and even the update of bootloader and softdevice is fine.
In a new case we had...
I'm still newbie of BLE developer, and designing a BLE device based on nrf51822 (whose service uuid is partially used for identification of serial number).
Like nordic's...
We want to design our own custom USB Dongle for connecting our sensor board to a PC. Sensor board has a nRF51 chip using Gazell protocol to transmit sensor data and also softdevice...
I am using keil compiler. The nRF51822 stack succesfuly compiled and also i am created the hex.I don't have j-link programmer but i will try to download using Ulink2 can u...
I meet a trouble like this:
My colleague used " nRF51822 QFAAC0 1322AW " to make a product. The KEIL program "based on s110_nrf51822_5.2.1_softdevice.hex and nRF51 SDK...
When nrf51822 with 32KB RAM will available? If it is going to be delayed is it possible to get samples? (I like to try IOT SDK and with my PCA10001 the heap overflows.)
...
If I don't call nrf_gzll_set_base_address_0(...) or nrf_gzll_set_base_address_1(...) what address will it use?
Also, what is the default number of send attempts?
Hi, I purchased and received the pca100028/nRF51-DK on Friday (12/19).
I've upgraded to Keil 5.12, loaded the 7.10 sdk pack, loaded the radio_test_pca100028 example ( I...
Hi
The datasheet for nRF24le1 seems to describe two ways to find out if the TX buffer is full.
Register map 07, STATUS, bit 0, TX_FULL
Register map 17...
