Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi,
With S132 it is possible to advertise on specific channel.
See devzone.nordicsemi.com/.../
But, since from BLE5 advertisement can be done on any of the 40 channels...
Hardware: redbearlabs Nano V2 (see pinout below)
Programmer: DAPLink v1.5 supplied by redbear
IDE: Arduino with the redbearlab nano 2 board package
The schematic can...
I'm writing an Android application that connects to various BLE peripherals including the NRF51 and NRF52. I don't know if this question is appropriate for this site, but...
Hi,
we are trying to disable 2 of 3 advertising channels on nRF52832 SoC with the softdevice S132 (1.0.0-3.alpha) installed. The example project ble_app_beacon works well...
hi
I am using ESB_DPL protocol between 51822 and 24LE1, and i used the sdk 12.2 examples/proprietary_rf/esb_ptx.
In my case, 51822 sent some packages with PTX mode,...
Hi,
I am interested to hear if anybody knows if it's possible to use 6LoWPAN on an iOS device together with nRF52832 ? I tried searching online but have not got any hits...
Hello,
I'm working on an application where we have a number of sensors and a radio that each require a connection to the nRF52. Specifically, 4 of these peripherals need...
DFU & UICR works well. However, concerning sw protection, we found that the binary file in the ZIP package of DFU is open to access. That is a security breach. Is any solution...
I have started to implement bootloader for 52832 and checked out "Secure DFU Serial" example from SDK v13.0 with Segger Embedded Studio.
I checked out this question devzone...
Our current project (custom nrf52 board SDK12.2) is set up as a peripheral device with the phone being the central device. This nrf52 device is plugged in and power consumption...
I continue to debug, via remote control on the other side of the world, a particularly nasty issue that is occurring in only certain units of a device. I had been blaming...
Hi,
I am trying to add saadc sample code to ble_blinky sample code. But I faced a problem. It seems that the sdk_config.h file is not recognized by the sample code. and...
HI, i m beginner in TWI with nrf52832. i want to write a bit in a registre of hmc5883l but i didnt succeed. what i want to do is :
writeByte(devAddr, regAddr, b) ==> (...
I would like to implement the mbed-os uVisor on a NRF52832.
Therefore I need to specify some addresses in the provided linker file.
Now the file: mbed-os/targets/TARGET_NORDIC...
