I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi
I'm interfacing MMA8452Q with nrf51822 using TWI all read-write function working fine but when I try to read acceleration data nrf_drv_twi_rx & nrf_drv_twi_tx function...
I am porting our sdk 8 based firmware for the sdk 11. Now the code crashes at the code below:
err_code = sd_ble_gap_device_name_set(&sec_mode,
(const uint8_t *)name,...
We followed the instructions for the beacon example for nrf 52 dk.
Multiple attempts to change and reset the board, there was no change in the ad packet.
Can someone...
I'm using the nRF52832 chip without an external crystal. I configured it to use the internal RC with:
nrf_clock_lf_cfg_t clock_lf_cfg;
clock_lf_cfg.source = NRF_CLOCK_LF_SRC_RC;...
Hi,
I have tested ble_app_hids_keyboard for using whitelist.I find that this example is bond+whitelist. If bonded, the peer address will be added into whitelist. But when...
Hi,
I test Whitelist function in the example ble_app_hids_keyboard_pca10040_s132 using SDK12.2.0.
I donnot understand the code in "case BLE_ADV_EVT_WHITELIST_REQUEST:" located...
Hi all,
I have some problems with GPIO Interrupts.
I'm using nrf52832, s132 and sdk 12.2
The error is totally random so I don't know why is generated. The case is...
Hi,
We are using the Secure DFU from SDK 12.2, with SD132 3.1.0, on a PCA10040.
As a DFU controller, we use a PCA10031 with a SD130 2.0.1 and a project derived from the...
Hello,
We are migrating from IAR 760 to IAR 8.10 compiler does not produce the same assembly for the SDK12 inline function nrf_delay_us.
The original C Function is :
...
Hi, i am working on RTLS project. In beacons i want to enable DFU service using SDK 13.0. But I could'nt find a gothrough process to do the same. Please give me some link...
I am using S132 4.0.2 and SDK 13, and I have theese questions:
I have an application where BLE node establishes multiple concurrent connections (several as central...
Hello,
I'm having systematically an HardFault interrupt ~10 seconds after calling sd_soft_device_enable(NULL, &fault_handler);
This occurs on my bootloader code, but...
Hallo Community,
I am doing the example ble_app_uart using Eclipse, a SDK 13.00 and a board 10040, When i compile the main file I´ve problems with scan params:
#if ...
