I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
What is the Characteristic UUID 0x2AA6
It shows up as the 4th Charateristic under the Generic Access Service, in the nrf5-ble-tutorial-characteristic-CompletedCode ported...
Hi all. i am using hid device keyboard example for nrf5. But when I try to call
sd_ble_gatts_hvx(p_hids->conn_handle, &hvx_params), this function returns error code 0x00003401...
Hi,
I am using the S120 stack and wish to connect and control as quickly as possible to the peripheral. The central and peripheral devices are both embedded devices and are...
Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
I am using blenano with mbed compiler and a 24LC256 eeprom.
the output o screen I get is the no. of total chars, i.e, 65355. below is the code.
#include "mbed.h"
#include...
Hi guys,
I'm on Win7 and I'm writing data from libusb to nrf51 board, my code is
usb_bulk_write(dev_handle, 0x04, data, WRITE_SIZE, 1000);
When the nrf51 receives...
Hello:
I tried to find this in the documentation but could not. Regarding the external trigger to the PPK (TRIG IN pin). Does this require a high-to-low transition, a low...
Do I need a custom 128-bit UUID if I delete one or more Characteristic from an Adopted Service
I do not modify the remaining Characteristics
For instance: Sniffing with...
I'm trying to program Sparkfun nRF52832 board using SWD (via nRF52 DK). I've erased original bootloader/softdevice/app and programmed S132 and my app. The app works, but only...
Hello,
I'm beginner for NRF51822. I have tried ble_app_hids_keyboard example on NRF51822 with s130 softdevice.
It is discoverable in smartphone as Nordic_Keyboard. Smartphone...
We have been using the DFU that came with the sdk 12.1 with a modification (essentially removing the button from the DFU code). We currently send an application command that...
Hardware:
I have an nRF52 device running the S132 running as a Central.
I have 6 iOS/Android devices running as peripherals.
Background:
I am attempting to have my central...
Hello,
is there any good example available, with whom I can simulate, that there are two devices are already connected and the host is scanning for some other devices?...
I am trying to use the function or any function with my BLE UART application. I have a timer that expires to kickoff reading of some sensors and then when I try to read my...
Hi all,
i m connect a sensor with Nrf51822 beacon and get the data.
so i want to transfer those data to Nrf51 dk kit continuously.
where i want to change or put my data...
