Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
Just want to confirm I can be i2c master with zephyr rtos for nrf52 pca10040.
In link ( devzone.nordicsemi.com/.../) titled "nRF5x support within the Zephyr Project RTOS...
Hello everybody!
I have one nrf52840 DK and nrf528323 DK. I was flashed and test throughput example. I reach 450kbps. ( transfer 1Mbyte in 18s). Can I enhance this speed...
Hi,
We are interested in nRF52840 and we know that nRF52840 supports both on IEEE 802.15.4(Thread, ZigBee) and IEEE 802.15.1(BLE).
However, does nRF52840 can run BLE...
HI
I'm studying how to control mouse and keyboard via HID with nRF24LU1+ module referring to firmware of nAN-22.
Even though I set Descriptor as appropriate for mouse...
I'm using FDS and define record_chunk.length_words 173.
system waits for fds operation is finished and in the meanwhile, system sleeps using sd_app_wait().
Then, sd_app_evt_wait...
Hello
i am using BLE Relay example with softdevices 132 and sdk version 13.
i make this example simple, no more connection.
just adverting and scanning continuously. here...
Hi all,
I'm using nRF52840 and S140 based on the ble_app_uart example. I get a error code 4 when use sd_ble_gatts_characteristic_add to add a characteristic for another...
Hello,
Help me, please.
I am testing ble_app_uart. Softdevice is S130 and SDK is nRF5_SDK_12.2.0_f012efa.
My development board is Waveshare's NRF51822 Eval Kit.
...
Hello,
I'm writing an application that uses the SAADC and would like to set up a high limit to trigger on.
If I use the following code, I'm able to trigger 1 ADC sample...
Hi,
I plan to design a system of 51822 that includes 1 center and 2 devices. And 8K Bytes data should be transmited from each device to the center per second simultaneously...
Hi, I am using a two nRF24L0+'s.
One for TX and one for RX. Transmitting in one direction only. There is sometimes a packet arriving out of order. Every minute or two....
I use ESB sample code ,change to do 8k sample rate ADC(10bit) and transport by ESB ,but overflow when output receive data to PC use uart at UARTE_BAUDRATE_BAUDRATE_Baud1M...
