I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi, I am confused by this config.
static void drv_keyboard_gpio_init(void) { // Make sure that columns will drive 0 when they will be configured as outputs. NRF_GPIO->OUTCLR...
I'm using a NRF52840 with S140 softdevice. I advertise some data and I want to be notified when advertising start. I followed this thread and I use the customs ble_radio_notification...
Dear Nordic Team,
Thanks for supporting.
Still i am work with keil IDE. But now i want to go work with Segger embedded studio because of mesh concept. Please give me step...
I have combined light switch client and ble_app_uart example by following this guide and this case ,but after I added the codes :
#define MESH_SOC_OBSERVER_PRIO //<set...
Hi,
I am developing stuff for a bike and need the Bluetooth Cycling Power Service 0x1818
I found the 0x1816 Cycling Cadence and Speed
Has anybody developed this service...
Hello I'm a beginner and I try to use the DFU. I use the documentation and I can send my init packet without any problem. But when I try to send my Firmware I have 2 problems...
Hi,
Our system is based on the nrf52832 with SDK BLE_2.0.1 for the mesh. I have few queries as per below,
1)It would be great if you could suggest any vendor who is working...
When Going into Sleep, I see peaks of 12mA every 30ms (see image) I'm assuming I can adjust that changing the connection interval settings. I have my Connection intervals...
I'm having some issues with the freeRTOS example in SDK 15. I've always seemed to find a hardfault which limits the MTU size to 176. Now when I try and set the connection...
Hi,
I have a question regarding fast/slow advertising
I'd like to advertise for 180s using a 100ms interval, then switch to a 1s interval, preferably for ever. I set...
I would like to use ADXL335 accelerometer in this nrf52832 custom kit Hackable . I don't have a J-Link but i have this custom programmer Bumpy which is based on the Black...
Hi,
How can wake my nrf52832 based module from system off sleep mode. i am using ' nrf_pwr_mgmt_shutdown()' / ' sd_power_system_off (); 'function to put the device into...
softdevice 6.0.0 SDK15.0.0 How do I use ble_app_hrs sample code add buttonless_dfu function? I flow the steps, but I am fail. 1. In ble_app_hrs project... add nRF_DFU folder...
